Mitsubishi HC3 User Manual download pdf (Page 15)

EN – 15

ENGLISH

VOLUME 15

Volume from the speaker

Press the VOLUME + or – button to change the

volume from the speaker.

The volume control bar will appear on the screen.

• The volume control bar will disappear about 10

seconds after the VOLUME button is released.

• The VOLUME buttons don’t function while the

menu selection bar or the menu is being

displayed.

• When a high-level audio signal, such as a DVD

audio signal, is supplied to the AUDIO IN

terminal, the output from the speaker may be

distorted.

Mute

The audio signal is temporarily muted when the

MUTE button is pressed. To cancel muting, press the

MUTE button again.

16:9/4:3 button

When ANAMORPHIC in the FEATURE menu has

been set to AUTO, the aspect ratio of the image

becomes 16:9 when VIDEO is chosen as the source. If

necessary, change the aspect ratio by pressing the

16:9/4:3 button. You can also change the aspect ratio

by setting ANAMORPHIC in the FEATURE menu.

REAL mode

By pressing the REAL button on the remote control,

you can view the screen displaying the picture as its

original size (native resolution display).

• The REAL mode may not function depending on the

input signal. For more details, refer to page 32.

Caution:

• After using the projector, wait one minute for the

air outlet fans to stop. Then unplug the power

cord from the wall outlet.

• The lamp can’t be lit again for one minute after

turned off for safety purpose. It will take another

one minute for the STATUS indicator to go out. If

you want to turn on the projector again, wait until

the indicator goes out, and then press the POWER

button.

• The air outlet fans rotate faster as the

temperature around the projector rises.

• When the temperature around the projector rises

high, the sign “TEMPERATURE!!” blinks red on

the screen. If the temperature stays high, the

lamp will go out automatically.

Power-off

Use the following procedure to turn off the projector.

Do not turn off the projector by unplugging the power

cord while the lamp is on. Unplugging while the lamp

is on degrades the lamp’s performance and causes

failure in the projector.

1. Press the POWER button.

• The message “POWER OFF? YES : PRESS

AGAIN” appears on the screen.

•To cancel, press any button except the POWER

button. (Some buttons on the remote control

don’t function for cancel.)

2.Press the POWER button within 10 seconds again.

• The lamp will go out and the STATUS

indicator will start blinking.

• Though the lamp goes out at this second press

of the POWER button, the air outlet fans

continue operating for one minute to cool down

the lamp and LCD panels. The STATUS

indicator will stop blinking.

3. Unplug the power cord.

• The POWER indicator will go out.

• If the power cord should be unplugged

accidentally while either the air inlet fan or the

air outlet fans are operating or the lamp is on,

allow the projector to cool down for 10 minutes

with the power off. To light the lamp again,

press the POWER button. If the lamp doesn’t

light up immediately, repeat pressing the

POWER button two or three times. If it should

still fail to light up, replace the lamp.

Important:

• When storing the projector in the provided

carrying case, the lens should face up.

AUTO POSITION button

When the image isn’t projected in the right position

with COMPUTER selected as the input source, follow

the procedure below.

1. Project a bright image such as the “Recycle Bin”

window on the full screen.

2. If the screen saver is running, turn it off.

3. Press the AUTO POSITION button.

• If the image is still not in the right position,

adjust the image position using the SIGNAL

menu.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 33 34

Comments to this Manuals

No comments

Mitsubishi HC3 User Manual Page 15

Comments to this Manuals

Related products and manuals for Data projectors Mitsubishi HC3