Mitsubishi Trim 110 Operations Instructions

DPX System Operating Instructions555 Theodore Fremd Ave., Rye, NY 10580 • 914-925-3261 • http://techsupport.mitsubishiimaging.com

3. Press CTRL + ALT and keep them pressedwhile pressing theDELETE key.The Log-In screen will appear ensuring the correctsetup. The default setup is no

During normal operation 4 programmes areneeded.Program RipManagerManagerRipMate PlateSetterMonitorThe above icons represent the available pro-grammes,

Active QueueThis queue shows all jobs ready for processing.The jobs will be processed in top-down order.Held QueueThis queue shows already processed j

3. Press the left mouse button and hold it downwhile pulling the job from the Held Queue tothe Active Queue. Release the mouse button.The job has now

2. Otherwise, select Start Inputs from the Rip-Mate menu in RipMate.The connection to the front-end will now be estab-lished.Monitoring the RIPThe Rip

Liquid Level: The level in the activator tank is tolow. Change the chemistry or refill the replenish-ment bottlesDrive Load: The processor stopped due

The information reflects the currently loaded cas-sette.4. Select the magazine which should be loaded byactivating the small radio button to the left

2. If the length is zero enter the number of metresjust loaded.3. Use the mouse to click on the Load button inorder to start the inlet roller drive mo

7.Click Form Feed.8.Click YES to form feed a plate.Repeat the last two steps until all exposed materialis fed.9.Click OK.10. Iconise the RipMagager by

5. Unplug the cable for the heating element un-derneath the processor module.6. Release the draining hoses and insert each oneinto a separate empty co

Purup-Eskofot A/SCopenhagen DivisionIndustriparken 35-37DK-2750 BallerupDenmarkTel.: (+45) 4473 6666Fax.: (+45) 4473 6767DPX System - Operating Instru

4. Lift the two processor racks from the tanks andclean them with a soft brush and lukewarmwater.5. Clean the activator and stabilizer tanks bypooring

Warning: Never turn on the power unless theprocessor module is filled or the power plug forthe heating element is removed, as this may causeoverheatin

TEM, due to Windows NT system or anotherprogramme.1. Try repeating the job.Undefined command “set calibration”The current plate setup can not find a c

3. Check the two punch tubes and punch tools forpunch waste. Make sure they can move freelyby turning them by hand.4. Close the exposure module door (

5. Lift the dryer module as shown on the picture.Check if there is a plate in the dryer section. If not,close the exposure module door (fig. 2. E) and

2.Technical SpecificationsDPX SYSTEM Digital PlatesetterType: Digital Plate Exposure SystemMax. plate format: 460 x 550 mm / 16.5 x 21.6"Max. ima

555 Theodore Fremd Ave., Rye, NY 10580 • 914-925-3261 • http://techsupport.mitsubishiimaging.com

Whilst every care has been taken in the preparation of this manual, no liability will beaccepted by Purup-Eskofot A/S arising out of any inaccuracies

555 Theodore Fremd Ave., Rye, NY 10580 • 914-925-3261 • http://techsupport.mitsubishiimaging.com

ContentsDescription . . . . . . . . . . . . . . . . . . . . . . . . . 2Computer-to-Plate System (CtP)Time Saving . . . . . . . . . . . . . . . . . . .

555 Theodore Fremd Ave., Rye, NY 10580 • 914-925-3261 • http://techsupport.mitsubishiimaging.com

1.DescriptionComputer-to-Plate System (CtP)The DPX SYSTEM digital platesetter producespress-ready plates for a variety of printing jobs.The entire pro

E. Processor module doorF. Locking pawl for processor module doorG. Plate exposure module doorH. Locking pawl for plate exposure module doorI. Roll ma

posed from left to right by the imagesetter, fig.3G.4. After exposure the plate is guided towards thedrum exit guide, fig. 5. During the forward mo-ti