Mitsubishi A8GT-50KBF User Manual

A8GT-50KBFExternal I/O Interface ModuleUser’s Manual(Hardware)Thank you for choosing the MELSEC-GOT Series.To ensure correct use of this equipment, pl

4External Connector Pin-OutsView from the unit front Connector used: Fujitsu's FCN-365P040-AUB1 B2 B3 B4 B5 B6 B7 B8 B9 B10B11B12B13B14B15B16B17B

5External Connection Diagram (1) (8-point inputs, 16-point outputs)XD1XD2XD3XD4XD5XD6XD7A8B7A7B6A6B5A5XSCN0XSCN1XSCN2XSCN3XSCN4XSCN5XSCN6XSCN7A16 YD1B

6External Connection Diagram (2) (64-point inputs, 16-point outputs)DC12/24V(12/24VDC)A17,B17,A180109111921293139020A121A222A323A030B131B232B333B040C1

7 4. System Configuration (1) System configurations and connection conditionsThe following system configuration assumes connection of a printer.The n

8(2) System equipmentThe following table indicates the system equipment needed forconnection of external I/O equipment.TypeImage No. ApplocationGOT un

9 5. User-fabricated Connection Cables The following is the way of fabricating the connection cable which can befabricated by the user:5.1 Connection

10(b) Parts listNumber Name Type Maker1) 2) Connector (with cover) A6CON1MitsubishiElectric1) Connector FCN-361JO40-AU2) Connector cover FCN-360CO40-B

11(2) Cable for connection between external I/O unit and terminal blockconversion unit.Fabricate the connection cable in accordance with the following

12(b) Parts listNumber Name Type Maker1) 2) Connector (with cover) A6CON1MitsubishiElectric1) Connector FCN-361JO40-AU2) Connector cover FCN-360CO40-B

135.2 Wring diagrams(1) Wiring diagram for use between external I/O unit and connector terminalblock conversion unit(a) For use of the connector termi

A-1DANGERCAUTION! SAFETY PRECAUTIONS !(Always read before starting use)When using Mitsubishi equipment, thoroughly read this manual and theassociated

14(b) For use of the connection terminal block conversion unit (A6TBY54-E)XD0XD1XD2XD3XD4XD5XD6XD7XSCN0YD0DC12/24VEmptyFGXSCN1XSCN2XSCN3XSCN4XSCN5XSCN

15(2) Connection of external inputs and external outputs to the connectorterminal block conversion unit.(a) For use of the connector terminal block co

16(b) For use of the terminal block conversion unit (A6TBY54-E)383028201810080XD03931292119110901XD13A322A221A120A02XD23B332B231B130B03XD33C342C241C14

17 6. Pates Identification A8GT-50KBF2) 4) 2) 1) 3) No. Name Description1)I/O cable connectioninterfaceInterface for connection of the I/O cable2) Un

18 7. Installation Procedure Install the unit to the GOT in the following procedure:(1) Thread External I/O unit mounting screw holes in the control b

19 8. Outline Dimension Drawing 3.2(0.13)A8GT-50KBF42.6 (1.68)65 (2.56)3.5 (0.14)73 (2.87)92 (3.62)44 (1.73)105 (4.13)500 (19.69)67.8 (2.67)9.5(0.37)M

20

21

WarrantyMitsubishi will not be held liable for damage caused by factors found not to be the cause ofMitsubishi; machine damage or lost profits caused

A-2[INSTALLATION PRECAUTIONS]DANGER! When installing and removing this module from the GOT main module besure to shut off the power at all external sw

A-3[STARTING AND MAINTENANCE PRECAUTIONS]DANGER! Do not change the switch setting while power is on.! Switch all phases of the GOT external power supp

A-4Revisions* The manual number is noted at the lower left of the back cover.Print Date *Manual Number RevisionJun., 1997 IB(NA)-68908-A First printin

A-5 CONTENTS 1. Overview... 12. Components Includ

1 1. Overview This user's manual gives the specifications, system configurations, partsidentifi-cation, installation procedure and outline dimens

2 3. Specifications Input SpecificationsInput system Dynamic scanNumber of input points 8/64 pointsIsolation system Photocoupler isolationRated input

3I/O SpecificationsExternal connection system 40-pin connectorApplicable wire size 0.3mm2Operation indicator NoneVoltage*312/24VDC(10.2 to 26.4V, ripp