1 This installation manual describes how to install the MA Remote Controller for use with Mitsubishi Building Air Conditioning System, direct expan
– 10 –9. Turning on the powerMake sure that the MA remote controller is properly installed according to the instructions in the Installation Manual an
11 (2) Clock setting(3) Main display settingUse the F3 or F4 button to select the display mode Full or Basic. (The factory setting is "Ful
– 12 –[3]Room temperature display[4]Auto mode display setting(6) Auto mode setting(7) Administrator password setting(8) Language selection[Button oper
– 13 –12. Service menu (Maintenance password is required.)At the Main display, press the MENU button and select “Service” to make the maintenance sett
– 14 –Table1. Function setting options(4) LOSSNAY setting (City Multi only)This setting is required only when the operation of City Multi units is int
– 15 –(5) Check(6) Diagnostic function.To search for the LOSSNAY address[4] Enter the address of the indoor unit to which the remote controller is con
– 16 –(7) Setting the maintenance passwordTake the following steps to change the maintenance password.13. Remote controller checkWhen the remote contr
1 Diese Installationsanleitung beschreibt das Installieren der MA-Fernsteuerung zur Verwendung mit Gebäude-Klimagerätesystemen von Mitsubishi, dem
2 WARNUNG VORSICHT WARNUNG VORSICHT WARNUNG
3 2. SystemanforderungenZum Ausführen der Handbuch-Navigationssoftware muss Ihr Computer die folgenden Voraussetzungen erfüllen:[PC] PC/AT kompa
2 WARNING CAUTION WARNING CAUTION WARNING CAUTION Precautions du
4 4. Vor Ort zu beschaffende Teile/Notwendige Werkzeuge(1) Vor Ort zu beschaffende TeileDie folgenden Teile sind vor Ort zu beschaffen:(2) Vor Ort
5 6. Installation/Verkabelung4 Schließen Sie das Fernsteuerungskabel an den Anschlussblock des Untergehäuses an.Entfernen Sie 6 mm der Ummantelung
6 5 Befestigen Sie das Untergehäuse. Installation mithilfe eines Schaltkastens Verschrauben Sie mindestens zwei Ecken des Schaltkastens. Wandins
7 8 Führen Sie das Kabel zum Obergehäuse.9 Bringen Sie die vordere Abdeckung und das Obergehäuse am Untergehäuse an.Es befinden sich zwei Befestigu
8 7. Wichtig Es kann zu einer Abweichung zwischen der an der Wand gemessenen Raumtemperatur und der tatsächlichen Raumtemperatur kommen.Beim Vorli
9 8. Tastenfunktionen der FernbedienungTastenbedienung im Hauptmenü(7) LCD mit Hintergrundbeleuchtung(2) Funktionstasten F1, F2, F3 und F4 von
10 9. Einschalten der StromversorgungVergewissern Sie sich, dass die MA-Fernbedienung ordnungsgemäß entsprechend den Anleitungen im Installationsha
11 (2) Uhreinstellung(3) HauptdisplayeinstellungWählen Sie mit Hilfe der F3- oder F4-Taste den Anzeigemodus Komplett oder Einfach aus. (Die Wer
12 [3]Raumtemperaturanzeige[4]Automatik-Anzeigeeinstellung(6) Automatikeinstellung(7) Administrator-Passworteinstellung(8) Sprachauswahl[Tastenbedi
13 12. Service-Menü (Wartungspasswort ist erforderlich.)Drücken Sie im Hauptdisplay die MENÜ-Taste und wählen Sie dann Service aus, um die Wartun
3 2. System RequirementsYour computer must meet the following requirements to run Manual Navigation Software.[PC] PC/AT compatible[CPU] Core2 Du
14 Tabelle 1. Funktionseinstellungsoptionen(4) LOSSNAY-Einstellung (nur City Multi)Diese Einstellung ist nur erforderlich, wenn der Betrieb der Ci
15 (5) Prüfen(6) Diagnosefunktion.Zum Suchen einer LOSSNAY-Adresse[4] Geben Sie die Adresse des Innengeräts ein, an das die Fernbedienung angeschlo
16 (7) Festlegen des WartungspasswortsGehen Sie zum Ändern des Wartungspassworts wie nachfolgend beschrieben vor.13. Fernbedienung prüfenWenn die F
4 4. Field-supplied parts/Required tools(1) Field-supplied partsThe following parts are field-supplied parts.(2) Field-supplied tools Flat-tip scr
5 6. Installation/Wiring work4 Connect the remote controller cable to the terminal block on the bottom case.Peel off 6 mm of the remote controller
6 5 Install the bottom case. Installation using a switch box Secure at least two corners of the switch box with screws. Direct wall installation
7 8 Route the wire to the top case.9 Install the front cover and top case on the bottom case.Two mounting tabs are at the top of the top case. (A c
8 7. Important Discrepancy between the indoor temperature measured at the wall and the actual indoor temperature may occur.If the following condit
9 8. Remote controller button functionsButton operations on the Main menu(7) Backlit LCD(2) Function buttons F1, F2, F3, and F4 from the left(
Comments to this Manuals