Mitsubishi GOT1000 GT15 User Manual

GOT1000CC-Link communication unitUser’s ManualGT15-75J61BT13-ZINDUSTRIAL AUTOMATIONMITSUBISHI ELECTRICMITSUBISHI ELECTRICArt. no. 169264IB(NA)-0800316

A-9ManualsThe following shows manuals relevant to this product.For relevant manuals, refer to the PDF manual stored within the drawing software used.D

11. OverviewThis user’s manual introduces the GT15 CC-Link communication unit (hereinafter referred to as GT15-75J61BT13-Z) used in the Control &

22. Performance SpecificationsThe following is the performance specification of CC-Link communication unit.For the general specifications of CC-Link c

3*1 : The vibration resistance of the CC-Link communication unit is as follows. (Differs with the GT15.)*2 : Each of the I/O signals (RX, RY) occupies

43. I/O Signals and Remote Register Assignment3.1 I/O Signals Transferred to/from the Master ModuleThe following table lists the I/O signals assigned

53.2 Remote Register AssignmentThe following is the assignment of the remote registers of the GOT.The remote registers differ according to the set num

64. Part Names and the SettingsThis section provides the names of the A8GT-J61BT13 and GT15-75IF900 parts and how to set the switches.A8GT-J61BT13GT15

7Number Name Description1) Mode setting switch Used to set the operating status of the module.(Factory setting:0)2) Station number setting switchesUse

8Number Name Description5) Indicator LEDs Data link status can be conformed by the on/off statuses of the LEDs.6) Connector Connector for connection t

95. Installation Procedure(1) Power off the GOT.(2) Remove the two extension unit covers of the GOT.(3) Fit the GT15-75IF900 along the groove of the G

A-1zSAFETY PRECAUTIONSz(Always read these instructions before using this equipment.)Before using this product, please read this manual and the relevan

10(5) Attach the communication unit fixing brackets (3 places) to GT15-75IF900, then fasten them with tightening torque of 0.36 to 0.48 N•m.(6) Mount

116. Wiring MethodThe following diagram shows how to wire the GOT and CC-Link system modules.(1) Wiring the GOT and CC-Link system modules by CC-Link

127. External Dimensions(1) GT15-75IF900Unit:mm (inch)(2) A8GT-J61BT13Unit:mm (inch)Dimensions of X when mounted to the GOT.15”, 12.1”, 10.4” 13.5 (0.

WarrantyMitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused

HEADQUARTERSEUROPEMITSUBISHI ELECTRIC EUROPE B.V.German BranchGothaer Straße 8D-40880 RatingenPhone: +49 (0)2102 / 486-0Fax: +49 (0)2102 / 486-1120CZE

A-2[DESIGN PRECAUTIONS][INSTALLATION PRECAUTIONS]z Some faults of this unit may keep the outputs on or off. An external monitoring circuit should ther

A-3[INSTALLATION PRECAUTIONS][WIRING PRECAUTIONS]z Use this unit in the environment given in the general specifications of the GT15 User's Manual

A-4[WIRING PRECAUTIONS][TEST OPERATION PRECAUTIONS]z Be sure to tighten any unused terminal screws within a tightening torque range (0.36 to 0.48•Nm).

A-5[STARTUP AND MAINTENANCE PRECAUTIONS][DISPOSAL PRECAUTIONS]z Do not touch the terminals while power is on.Doing so can cause an electric shock or m

A-6[TRANSPORTATION PRECAUTIONS]z Make sure to transport the GOT main unit and/or relevant unit(s) in the manner they will not be exposed to the impact

A-7REVISIONS* The manual number is noted at the lower right of the top cover.© 2005 MITSUBISHI ELECTRIC CORPORATIONPrint Date *Manual Number RevisionJ

A-8CONTENTS1. Overview .......................... 12. Performance Speci