Mitsubishi M800 User Manual download pdf

Vehicle Installation Notes

Document Number DVIN0004

Title M800OEM - EVO47 and 8RS

Approved By JA

Revision Date Prepared By Change History

1 28/06/2002 AD Added EVO7 to pin 8 and 22, external TCA

2 22/04/2004 AD Added EVO8 RS changes

3 05/10/2004 DS Re-formatted – Doc Ref: VIAU0004 EVO47 Adaptor

23/8/2006

18/12/2006

New format

Added A/C information

Reproduction in whole or in part is prohibited without written approval from MoTeC Pty Ltd.

Mitsubishi EVO47

This Document refers to MoTeC M800 OEM installations to Mitsubishi Lancer Evo4, 5, 6, 7 and some

Evo8 models using the EVO47 adaptor (MoTeC Part No. 13005A). For all other applications please

refer to the correct installation notes.

Contents

• Introduction

• Parts Required

• Model Specific Information

• Thematic Fan Operation

• Input / Output Test

• TPS Setup

• Idle Setup

• Mass Air Flow

• Additional Sensors

• M800 Pinout

• OEM ECU Pinout

• Calibration Tables

• ECU Setup

• Link Table

• Communications and Lambda connector

Introduction

The MoTeC M800 OEM is a MoTeC M800 ECU with an adaptor board that allows it to plug directly

into the cars original wiring. ECU functionality is the same as the MoTeC M800 with the exception of

peak and hold injector drive function which is not possible on the M800 OEM. Only high

impedance injectors or low impedance injectors with a suitable resistor can be used with the M800

OEM. Mitsubishi Evo4-8s have a resistor pack installed in the injector circuit with low impedance

injectors.

The EVO47 M800 Adaptor is an interface that allows an M800 OEM to be mounted in the factory

ECU case for a Mitsubishi Lancer EVO4 - 8 (four plug connector). This document describes the

details of the EVO47 adaptor and the configuration options that are available.

There are two versions of the EVO8. One version uses an ECU with a four plug main connector. This

vehicle is supported by the EVO47 OEM adaptor as described in this document. It is also supported

by the EVO48 (MoTeC part no.13009A) which supersedes the EVO47 and is covered in a separate

1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - Vehicle Installation Notes

Vehicle Installation Notes Document Number DVIN0004 Title M800OEM - EVO47 and 8RS Approved By JA Revision Date Prepared By Change History 1 28

Page 2 - Important Note!

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 10 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes AV7 43 Spa

Page 3 - Page 3 of 16

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 11 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes LA1P 75

Page 4 - Using the Pinout Diagram

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 12 of 16 OEM ECU Pinout Plug B59 Yellow Plug B60 Yellow Plug B61 Yellow Plug B62 Yellow21531

Page 5 - M800 Pinout

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 13 of 16 OEM Pin M800 Pin Function 41 O/C Not used 42 0V AUX Spare 0V pin 43 AV7 Spare A

Page 6

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 14 of 16 Calibration Tables Mass Air Flow Sensor DIG2 g/s 1 decimal place Input (Hz) 0.0 1

Page 7

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 15 of 16 Link Table Open Links Closed Links Function 01, 15 26 • AUX1 Lambda heater 01,

Page 8

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 16 of 16 On-board BAP sensor calibration – AV4 , Calibration = 62 Pressure kPa Vout (V) M80

Page 9

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 2 of 16 document. The other version uses an ECU with a three plug main connector which is s

Page 10

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 3 of 16 Model Specific Information EVO8 RS Mitsubishi has released two versions of the EVO8.

Page 11 - Communications

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 4 of 16 Additional Sensors It is possible to use un-assigned pins for additional sensors. T

Page 12 - OEM ECU Pinout

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 5 of 16 M800 Pinout Plug B59 Yellow Plug B60 Yellow Plug B61 Yellow Plug B62 Yellow2153164175

Page 13

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 6 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes INJ6 55, #39

Page 14 - Ignition Dwell Table

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 7 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes IGN3 21 #34

Page 15 - Link Table

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 8 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes AUX2 INT La

Page 16 - Lambda 2 Connector

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 9 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes Inputs REF

Mitsubishi M800 User Manual

Browse online or download User Manual for Mobile phones Mitsubishi M800. Vehicle Installation Notes

Summary of Contents

More documents for Mobile phones Mitsubishi M800

Comments to this Manuals

Mitsubishi M800 User Manual

Browse online or download User Manual for Mobile phones Mitsubishi M800. Vehicle Installation Notes

Summary of Contents

More documents for Mobile phones Mitsubishi M800

Comments to this Manuals

Related products and manuals for Mobile phones Mitsubishi M800