LAN Control UtilityUser Manual (for XD600U/XD600U-G/WD620U/WD620U-G)Contents1. Introduction ...
104. Projector registration4.1. Registration of projector to "ProjectorView Global+"The procedures to register projectors vary among the for
114. Projector registrationProcedure B - Connection example 3 (where projectors are installed via a router)To automatically detect projectors connecte
124. Projector registration<Note>• Set the default gateways of the projectors and PC correctly. For details, contact your network administrator.
134. Projector Registration4.2. When changing the projector IP settingsYou can change the projector IP settings.(1) Select the projector which you lik
144. Projector registration• "Edit Projector Setting" window is displayed.(3) Set the Projector Name and its group and enable or disable the
154. Projector registration4.4. When deleting projector registration(1) Select the projector which you like to delete from the projector list on the m
165. Operation of projector5.1. Operation of projector by remote controllerGroup or single unit of projector can be operated.(1) Select the projector
175. Operation of projector5.2. Confirmation of projector statusThe status of the projector can be confirmed.The status of the projector is displayed
186. Schedule setting6.1. Creation of projector groupMultiple projectors can be controlled and batched by sorting groups.Also, each group can set each
196. Schedule setting(7) Click [Add].<Note>• The power supply ON and the power supply OFF can not be selected at the same time of the same day o
21. Introduction1.1. Preparing to use network features• Installing the ProjectorView Global+• Assigning the projector IP address• Configuring settings
206. Schedule setting6.3. When deleting group(1) Select the group which you like to delete from the Group select pull-down menu on the main screen.(2)
217. Mail settingWhen the communication with the projector monitored by the theft detector is disrupted, a warning mail can be sent to the designated
228. ProjectorViewProjectorView is a web-browser based remote control and monitoring tool for network projectors.If you use the projectors listed in p
238. ProjectorView ProjectorView main window (REMOTE CONTROL)When you click REMOTE CONTROL, the Remote Control window is displayed. You can click the
248. ProjectorView<Note>• No E-mail messages are sent when a command error occurs.• For approx. 10 seconds after the projector is powered on, th
258. ProjectorViewThe following table explains each item.*1For data entry, use single-byte alphanumerical characters and symbols ( + - / = * _ ! ? . ,
268. ProjectorView(3) Enter the New network password and Confirm network password, and then click [OK].• If passwords entered match, the window closes
279. Visual PA (Visual PA enabled projectors only)Visual PA is a feature to display messages on the projector screen.It can be used for all active Vis
2810. Telnet setup (Telnet enabled projectors only)You can set the password for ProjectorView, a web-based remote control and monitoring tool for netw
2911. PJLink11.1. About PJLinkThis projector supports the industry standard protocol PJLink for projector control. It allows you to control and monito
31. IntroductionMicrosoft® and Windows® are the registered trademark or trademark of Microsoft Corporation in the United States and other countries.(T
3011. PJLinkThis projector, which is equipped with LAN terminal and manufactured by Mitsubishi Electric Corporation, is fully compliant to the specifi
3112. Others12.1. Troubleshooting• The projector can not be recognized.The projector may not be recognized automatically due to the setting of fire wa
42. Setup2.1. Installation of "ProjectorView Global+"Before starting installation, be sure to read "ReadMe.txt" contained in the C
52. Setup(5) When the installation has been completed, click [Close].2.2. When deleting "ProjectorView Global+" (Uninstallation)<Note>
62. Setup2.3. ConnectionConnect the controller PC and the projector, which have installed "ProjectorView Global+", to a commercially availab
73. Main screenA Menu bar Set Configuration Various settings can be configured, such as the new registration and editing of projector/group, mail sett
83. Main screenEXIT You can exit "ProjectorView Global+". However, you cannot exit the application during the automatic projector search and
93. Main screen3.1. System settings(1) Select "Edit System Info" from "Set Configuration" of the menu bar on the main screen.• &qu
Comments to this Manuals