Mitsubishi EQ-V680D1 User Manual download pdf

After the installation and wiring work, be sure to install the provided

terminal cover on the product when you want to activate and operate

the module. Failure to do so results in the risk of electric shock.

Fully mount the antenna cable to the module connector. After

mounting, check for separation. Insufficient contact results in the

risk of erroneous input and output.

Be sure to place the communication cables and power cables

connected to the module in a duct, or secure them with clamps.

Failure to do so results in the risk of cable movement and drift,

module or cable damage caused by careless pulling, and malfunction

caused by insufficient cable contact.

When connecting a cable, first verify the connection interface type

and then connect the cable properly. Connecting a cable to a

wrong interface or mis-wiring a cable results in the risk of

external device malfunction.

Tighten the screws within the specified torque range. If a screw

is too loose, a short circuit or malfunction may result. If a screw

is too tight, screw and/or module damage may occur, resulting

in a short circuit, or malfunction.

When removing a communication cable or power cable connected

to the module, do not pull the cable section. For cables with

connectors, hold the connector of the section connected to the

module during removal. For terminal block cables, loosen the

screws of the terminal block and then remove the cable. Pulling

a cable while it is connected to the module results in the risk of

malfunction and module and cable damage.

Be careful to prevent foreign matter such as dust or wiring chips

from entering the module.

Failure to do so may result in the risk of fire, failure, and malfunction.

EQ-V680D1

EQ-V680D2

EQ-V680D1

EQ-V680D2

Model

Manuals

Item

Manual 1

Ferrite core 1

90.5

(16)

(50)

27.4

Unit: mm

90.5

(16)

(50)

27.4

Unit: mm

(Connection example)

+24VDC

Line filter

Ring section

Item

1 unit 2 units

No.

RUN

BSY.

EQ-V680D1/EQ-V680D2

50CM-D180056-C(1404)MEE

SAFETY PRECAUTIONS

(Always read these precautions prior to use.)

Before using this product, please read this manual and the

relevant manuals introduced in this manual carefully and

pay full attention to safety to ensure that the product is

used correctly.

The precautions presented in this manual are concerned

with this product only.

For programmable controller system safety precautions,

refer to the user's manual of the CPU module used.

In this manual, the safety precautions are ranked as

"WARNING" and "CAUTION".

WARNING

CAUTION

Indicates that incorrect handling may

cause hazardous conditions, resulting

in death or severe injury.

Indicates that incorrect handling may

cause hazardous conditions, resulting

in medium or minor injury and/or

property damage.

Note that failure to observe the

CAUTION level

instructions may lead to a serious consequence according

to the circumstances. Always follow the precautions of both

levels because they are important to personal safety.

Please keep this manual in an easy-to-access location for

future reference, and be sure to deliver the manual to the

end user.

[INSTALLATION PRECAUTIONS]

The manuals related to this product include the following.

Feel free to order the manual if needed.

Detailed manuals

Manual Title

RFID Interface Module User's Manual

(Details)

Manual Number

50CM-D180057

Manual Title Manual Number

(1) This product

To make this product compliant with the EMC Directive and

Low Voltage Directive, the following countermeasure is required.

1. OVERVIEW

This user's manual describes the specifications, part names,

installation, wiring and connections with other devices, and

other information related to the EQ-V680D1/EQ-V680D2 RFID

interface module (hereinafter "RFID interface module") used in

combination with the MELSEC-Q series CPU module.

Once you have opened the product package, verify that the

package contains the following.

Quantity

RFID interface module main unit

2. PERFORMANCE SPECIFICATIONS

The following describes the performance specifications of the

RFID interface module. For the general specifications of the

RFID interface module, refer to the user's manual of the CPU

module used.

Specifications

Item

Specifications

Model

Manufactured by

Omron Corporation

Connectable antenna

No. of connectable

antennas

No. of occupied IO points

Data transfer volume

Power supply

Internal power supply

(supplied from inside

the 5VDC programmable

controller)

External power supply

24VDC

(20.4VDC to 26.4VDC)

EQ-V680D1

EQ-V680D2

V680-HA63A

+V680-HS

V680-HA63B

+V680-HS

V680-H01-V2

V680-HA63A

+V680-HS

V680-HA63B

+V680-HS

32 points (IO assignments

: 32 intelligent module points)

2048 bytes, maximum

0.42A

0.25A

0.52A

0.37A

3. MOUNTING AND INSTALLATION

3.1 Handling Precautions

3.2 Installation Environment

Refer to the user's manual of the CPU module used.

3.3 Cable Installation

When installing the antenna cable to the RFID interface

module, be sure that excessive external force is not

applied to the connector connecting area of the module.

4. PART NAMES AND SETTINGS

The following explains the names of each part of the RFID

interface module.

Description

Name

LED display

Test switch

Antenna

connector

Power supply

terminal

Indicates the operating status of the RFID

interface module.

[For display details, refer to Section (1).]

Used to switch between RUN mode and

TEST mode.

A connector for antenna connection.

A terminal for 24VDC power supply

connection.

(1) LED List

LED

Name

NOM.

ERR.

EXT.PW

Display Details

Indicates normal operation.

Indicates the operating

status of each channel.

Indicates the communication

completion status of each

channel.

Indicates whether or not an

error exists on each channel.

Indicates the status of the

power supply to the antenna.

: On

: OFF

Normal

Running

Normal

completion

Error

Normal

Abnormal

Waiting

Waiting or

abnormal

completion

Normal

Abnormal

5.2 Wiring the Power Supply Terminal

The following shows a wiring diagram of the power supply

terminal.

(1) A circuit (class 2 circuit) having a class 2 power supply

module in accordance with

UL1310 or a class 2 transformer in accordance with UL1585

as a power supply, and a maximum voltage of 30Vrms

(42.4 peak) or less.

Recommended DC power supply

Manufactured by Omron Corporation

(small-sized DIN rail installation type)

Model Output Capacity Input Voltage

S8VS-03024 24VDC, 1.3A

100 to 240VAC

While simply corrective action within the RFID interface

module is sufficient to counter the noise superimposed on

the power line, the noise to the ground can be significantly

reduced by supplying power via a line filter.

5.3 Inserting and Removing the Antenna and Cable

When inserting or removing an antenna or cable, follow the

procedures below.

(1) Insertion Method

[1] Hold the section of the connector that secures the cable

and insert the connector with the white dot facing upward.

[2] Push the connector straight in until the connector locks.

CAUTION

Do not insert the connector with the power

supply ON. Doing so results in the risk of failure.

The connector will not lock if you push the ring

section. Be sure to hold and push the section

that secures the cable.

The connector cannot be removed by holding

and pulling the section that secures the cable.

Pulling that section results in the risk of breakage

and damage. Do not pull the cable with force.

Do not remove the connector with the power

ON. Doing so results in the risk of failure.

Section that

secures the cable

Ring section

Section that

secures the cable

CAUTION

(2) Removal Method

[1] Hold onto the ring section and pull straight back.

6. EXTERNAL DIMENSIONS

(1) EQ-V680D1

R40 or more

(2) EQ-V680D2

Product Warranty Details

Please confirm the following product warranty details prior to

product use.

Gratis Warranty Terms and Gratis Warranty Range

If any fault or defect (hereinafter referred to as "Failure")

attributable to Mitsubishi Electric Engineering Company Limited

(hereinafter referred to as "MEE") should occur within the gratis

warranty period, MEE shall repair the product free of charge via

the distributor from whom you made your purchase.

Gratis Warranty Period

The gratis warranty period of this product shall be one (1)

year from the date of purchase or delivery to the designated

place. Note that after manufacture and shipment from MEE,

the maximum distribution period shall be six (6) months, and

the gratis warranty period after manufacturing shall be limited

to eighteen (18) months.

In addition, the gratis warranty period for repaired products

shall not exceed the gratis warranty period established prior

to repair.

Gratis Warranty Range

The gratis warranty range shall be limited to normal use based

on the usage conditions, methods and environment, etc.,

defined by the terms and precautions, etc., given in the

instruction manual, user's manual and caution labels on the

product.

Warranty Period after Discontinuation of Production

(1) MEE shall offer product repair services (fee applied) for

seven (7) years after production of the product has been

discontinued. Discontinuation of production shall be reported

via distributors.

(2) Product supply (including spare parts) is not possible after

production has been discontinued.

Exclusion of Opportunity Loss and Secondary Loss

from Warranty Liability

Regardless of the gratis warranty period, MEE shall not be

liable for compensation for damages arising from causes not

attributable to MEE, opportunity losses or lost profits incurred

by the user due to Failures of MEE products, damages or

secondary damages arising from special circumstances, whether

foreseen or unforeseen by MEE, compensation for accidents,

compensation for damages to products other than MEE products,

or compensation for other work carried out by the user.

Changes in Product Specifications

The specifications given in the catalogs, manuals and technical

documents are subject to change without notice.

This document is a new publication, effective April 2014.

Specifications are subject to change without notice.

The standard price does not include consumption tax.

Please note that consumption tax will be added at the time of

purchase.

Developed April 2014

50CM-D180056-C

[DESIGN PRECAUTIONS]

CAUTION

Provide a safety circuit outside the programmable

controller to ensure that the overall system operates

safely in the event of an error in the external power

supply or failure of the programmable controller itself.

Failure to do so results in the risk of erroneous output

and malfunction and, in turn, module failure.

CAUTION

Configure the circuitry so that the external power supply is

activated after the power supply of the programmable controller

itself. Activating the external power supply first results in the risk

of erroneous output and malfunction and, in turn, module failure.

When installing the RFID interface module and amplifier/antenna

cables, do not bundle the cables with or install the cables close

to the main circuit, power lines, or the like. Be sure to separate

the cables and lines by about 100mm or more. Failure to do so

will cause noise and, in turn, malfunction.

When storing the product, be sure to observe the defined storage

ambient temperature and humidity. Failure to do so will lead to

module malfunction and failure.

Look the control panel so that only those who trained with

enough knowledge about the electric facilities can be opened.

Install the emergency stop switch outside the control panel so

that workers can operate it easily.

CAUTION

Use the programmable controller in an environment that reflects

the general specifications stated in the user's manual of the CPU

module used. Using the programmable controller in an environment

out of the general specification range results in the risk of electric

shock, fire, malfunction, and product damage or deterioration.

During installation, fully insert the tabs used to secure the module

into the holes of the base unit while pressing down the module

mounting lever located at the bottom of the module. An incorrectly

mounted module results in the risk of malfunction, failure, and

dropping. When used in an environment of high oscillation, secure

the module with screws.

Tighten the screws within the specified torque range. If a screw

is too loose, a dropped module, short circuit, or malfunction may

result. If a screw is too tight, screw and/or module damage may

occur, resulting in a dropped module, short circuit, or malfunction.

CAUTION

Be sure to shut off all phases of the external power supply used

by the system before module installation or removal.

Failure to do so results in the risk of product damage.

Do not directly touch a powered section or electronic component

of the module. Doing so results in the risk of module malfunction

and failure.

[WIRING PRECAUTIONS]

CAUTION

RFID Interface Module

EQ-V680D1

EQ-V680D2

User's Manual

(Hardware)

Model

HEAD OFFICE:Hulic KUDAN BLDG.1-13-5, KUDANKITA CHIYODA-KU, TOKYO 102-0073, JAPAN

NAGOYA ENGINEERING OFFICE:139 SHIMOYASHIKICHO-SHIMOYASHIKI, KASUGAI, AICHI 486-0906, JAPAN

CAUTION

A protective film is attached to the top of the module to prevent

foreign matter, such as wire chips, from entering the module

during wiring.

Do not remove the film during wiring.

Remove it for heat dissipation before system operation.

Do not connect the power supply in reverse. Doing so results

in risk of failure.

Use the module after confirming that the external input DC power

supply is within the rated power supply voltage.

Failure to do so results in the risk of failure and malfunction.

Do not bundle the control or communication cables with or install

the cables close to the main circuit, power lines, or the like. Be

sure to separate the cables and lines by about 100mm or more.

QCPU User's Manual

(Hardware Design, Maintenance and Inspection)

Manufactured by Mitsubishi Electric Corporation

Mitsubishi general-purpose programmable controller

MELSEC-Q series manual

EQ-V680D1 EQ-V680D2

5. CONNECTING THE MODULE

5.1 Wiring Precautions

Connect the 24VDC power supply to the power supply of (1) below.

SH-080483ENG

To suppress radiation noise, use a ferrite core. The method

of use is as follows:

Bring together the power supply cable of the programmable

controller power supply module and the grounding wire and

route them through the ferrite core. The target position of the

ferrite core is within 10cm from the power supply module.

Authorized representative in Europe

Authorized representative in Europe is shown below.

Name :Mitsubishi Electric Europe B.V.

Address :Gothaer strasse 8, 40880 Ratingen, Germany

+24VDC

INPUT

100-240VAC

Programmable controller

Power

supply

CPU

module

Ferrite core

(within 10cm from the power supply contact)

Grounding

wire

Power supply

cable

EMC AND LOW VOLTAGE DIRECTIVES

Compliance to the EMC Directive, which is one of the EU Directives,

has been a legal obligation for the products sold in European countries

since 1996 as well as the Low Voltage Directive since 1997.

Manufacturers who recognize their products are compliant to the

EMC and Low Voltage Directives are required to declare that

print a "CE mark" on their products.

Outer dimensions 98(H) 27.4(W) 90.5(D)[mm]

Item

Specifications

Power supply

Weight

0.2kg

External power supply

connection terminal

2-point terminal block

Compatible crimp

contact lugs

1.25-3, R1.25-3

Connector connecting area

RFID interface module

Antenna cable

Installation bending radius:

40mm or greater

Secure in such a manner that external force is

not applied to the connector connecting area.

*1: "The Power Supply shall comply with the requirements in

the standard for an isolated secondary limited voltage, limited

current (LVLC) circuit, defined by UL508." or equivalent.

*2: For external power supply details, refer to Section 5.2.

Module screw (M3 screw)

0.52 to 0.57N m (4.6 to 5.1lbf in)

0.36 to 0.48N m (3.2 to 4.3lbf in)

(1) The RFID interface module case is made of plastic. Do

not drop the case or expose the case to strong impact.

(2) Before touching the module, be sure to touch grounded

metal or the like to release the static electricity from your

body.

(3) Tighten the module screws, etc., within the ranges

indicated below. Insufficient tightening results in the risk

of a short circuit, failure, and malfunction.

Screw Location

Tightening Torque Range

Power supply terminal block

screw (M3 screws)

*1: The module can be simply secured to the base unit by the

hooks located on top of the module. Note, however, that we

recommend securing the module using screws in locations

of high oscillation.

Wiring recommendations

Wire standard

Heat Resistant PVC Insulated Wire

JIS C 3316 HKIV,JIS C 3317 HIV,

UL 758 Style No.1007or1015

Temperature rating

Minimum 75℃

Voltage rating

300V to 600V

Conductors wire

size

AWG18(0.75mm

, 0.9mm

)

Conductors metal

Stranded copper

CAUTION

ATTENTION

Do not wire the cables near or bundle the cables with

main circuit cables, or power lines.

Doing so causes noise and surge impact, resulting in

the risk of malfunction. Be sure to separate the cables

and lines by about 100mm or more.

When using a group of equipment, such as inverters,

servo motors, and the like, be sure to execute class D

grounding (type 3 grounding). Failure to do so results in

the risk of magnetic field interference and malfunction.

Do not invert the EXT.PW polarity of an external power

supply during connection.

The RFID interface module will not operate.

Do not connect directly to line voltage. Line voltage

must be supplied by a suitable,approved isolating

transformer or power supply having short circuit capacity

not exceeding 100VA maximum or equivalent.

Ne pas se connecter directement à la tension de ligne.

La tension de ligne doit être fournie par un transformateur

d'isolement approprié et approuvé ou par un bloc

d'alimentation ayant une capacité de court-circuit ne

dépassant pas 100 VA au maximum ou équivalent.

Operating temperature

Operating humidity

5 to 95%RH

Pollution degree

Operating ambience

No corrosive gases

Operating altitude

Overvoltage category Ⅱ

Enclosure

0 to 55℃

(Maximum surrounding

air temperature 55℃)

0 to 2000m

open type equipment

(Must be mounted within

an enclosure.)

RFID Interface Module 1
(Hardware) 1

Summary of Contents

Page 1 - (Hardware)

After the installation and wiring work, be sure to install the provided terminal cover on the product when you want to activate and operate the module

Mitsubishi EQ-V680D1 User Manual

Browse online or download User Manual for Recording Equipment Mitsubishi EQ-V680D1. Mitsubishi EQ-V680D1 User`s manual

Summary of Contents

More documents for Recording Equipment Mitsubishi EQ-V680D1

Comments to this Manuals

Mitsubishi EQ-V680D1 User Manual

Browse online or download User Manual for Recording Equipment Mitsubishi EQ-V680D1. Mitsubishi EQ-V680D1 User`s manual

Summary of Contents

More documents for Recording Equipment Mitsubishi EQ-V680D1

Comments to this Manuals

Related products and manuals for Recording Equipment Mitsubishi EQ-V680D1