Mitsubishi S490 User Manual download pdf (Page 13)

´ EN – 13

ENGLISH

To operate projector power ON

• The picture might not be of optimum performance

in extreme hot or cold conditions. (The projector is

not malfunctioning.)

4. Press the ZOOM/FOCUS button to FOCUS. “FO-

CUS” will appear on the display.

5. Adjust with the + or - button to get a fine picture.

6. Press the ZOOM/FOCUS button to ZOOM. “ZOOM”

will appear on the display.

7. Adjust with the + or - button to get an approximate

size.

• Focus and zoom adjustment is possible in the normal

picture mode only. In PinP or EXPAND mode, the

adjustment is prohibited.

8. Select the desired external input source by using

the COMPUTER or VIDEO button.

• The projector automatically selects the appropriate

signal format. The selected signal format is dis-

played on the screen.

• The COMPUTER or VIDEO button does not work

when MENU is displayed. At this time, the prohibi-

tion mark ( ) appeares on the screen.

• When selecting the COMPUTER input, the image

may flicker. Press the $ or % button to adjust the

image.

• The intensity of the lamp will be STANDARD for 1

minute regardless of the setting of the LAMP MODE

when the lamp turns on.

For X500U only

• To view the digital input, select COMPUTER 1 in-

put and set the INPUT SELECT switch on the ter-

minal board to DIGITAL.

1. Turn on the equipment connected to the projector.

2. Put the projector into standby mode by pressing the

main power switch. The POWER indicator lights up

red.

3. Turn the projector on by pressing the POWER but-

ton. The light source lamp starts warming up, even-

tually turning completely on.

• When the light source lamp does not light up,

wait until the LAMP indicator is turned off, then

press the POWER button again.

• If the main power switch to the unit is turned

off within two minutes of turning off the light

source lamp, power will not be applied to the

lamp for one minute when the next time the

main unit power switch is turned on. When

this happens, the indicator lamp will blink for

one minute.

condition

indicator

LAMP

POWER

stand-by

red

when light source lamp is on

green

light source lamp held off temporarily

red

Important:

• A darkened image may be seen right after pressing

the POWER button due to warming up of this pro-

jector. While warming up, no other commands can

be accepted.

• After the power is turned on or the LAMP MODE is

changed, the screen may flicker before the lamp op-

eration becomes stable. This is due to the charac-

teristics of the lamp, not a failure of the lamp.

• When the lamp indicator is blinking red, the ser-

vice life of the lamp is about to end. Replace the

lamp. See pages 23 and 26.

LAMP

VOLUME

ZOOM/

FOCUS

KEYSTONE

TEMP

VIDEO

COMPUTER

MUTE

AUTO

POSITION

ENTER

AUTO POSITION

button

AUTO POSITION

button

MUTE button

ENTER

RIGHT CLICK

LASER

COMPUTER

VIDEO

ZOOM/

FOCUS

KEYSTONE

VOLUME

AUTO

POSITION

P in P

MUTE

EXPAND STILL

2 , 11

REMOTE

AUDIO 2 INCOMPUTER 2 IN

AUDIO OUTCOMPUTER OUT

AUDIO 1 INCOMPUTER 1 IN

DIGITAL

ANALOG

INPUT SELECT

MAIN

AC IN

S-VIDEO

VIDEO

AUDIO

VIDEO 1 IN VIDEO 2 IN

USB

RS-232C

3 , 9 , 10

4 , 6

5 , 7

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 35 36

Comments to this Manuals

No comments

Mitsubishi S490 User Manual Page 13

Comments to this Manuals

Related products and manuals for Data projectors Mitsubishi S490