Mitsubishi S490 User Manual download pdf (Page 2)

EN – 2

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of uninsulated “dangerous voltage” within

the product’s enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock.

The exclamation point within an equilat-

eral triangle is intended to alert the user

to the presence of important operating

and maintenance (servicing) instructions

in the literature accompanying the

appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE

THIS (POLARIZED) PLUG WITH AN EXTENSION

CORD, RECEPTACLE OR OTHER OUTLET UNLESS

THE BLADES CAN BE FULLY INSERTED TO

PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIP-

MENT, THE SOCKET-OUTLET SHALL BE IN-

STALLED NEAR THE EQUIPMENT AND SHALL BE

EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use

another power-supply cord, it may cause interference with

radio and television reception.

For X500U only

Use the attached RGB cable, RS-232C cable with this

equipment so as to keep interference within the limit of a

FCC Class A device.

For X490U / S490U only

Use the attached RGB cable, RS-232C cable with this

equipment so as to keep interference within the limit of a

FCC Class B device.

This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN

PROJECTOR IS IN THE POWER ON MODE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

COUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

For X500U only

COMPLIANCE NOTICE OF FCC

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment gener-

ates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.This

digital apparatus does not exceed the Class A limits for radio

noise emissions from digital apparatus as set out in the interfer-

ence-causing equipment standard entitled “Digital Apparatus”,

ICES-003 of the Department of Communications.

Changes or modifications not expressly approved by Mitsubishi

could void the user's authority to operate this equipment.

COMPLIANCE NOTICE OF INDUSTRY

CANADA

This Class A digital apparatus complies with Canadian ICES-

003.

For X490U / S490U only

COMPLIANCE NOTICE OF FCC

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced Radio / TV technician

for help.

Changes or modifications not expressly approved by Mitsubishi

could void the user's authority to operate this equipment.

COMPLIANCE NOTICE OF INDUSTRY

CANADA

This Class B digital apparatus complies with Canadian

ICES-003.

When using the projector in Europe

COMPLIANCE NOTICE

This LCD - Video Projector complies with the requirements

of the EC Directive 89/336/EEC “EMC Directive” and 73/

23/EEC “Low Voltage Directive” as amended by Directive

93/68/EEC.

The electro-magnetic susceptibility has been chosen at a

level that gains proper operation in residential areas, on

business and light industrial premises and on small-scale

enterprises, inside as well as outside of the buildings. All

places of operation are characterised by their connection to

the public low voltage power supply system.

WARNING

Use the attached RGB cable or RS-232C cable with this

equipment so as to keep interference within the limits of a

EN55022 Class B. Please follow WARNINGS instructions.

1 2 3 4 5 6 7 ... 35 36

Comments to this Manuals

No comments

Mitsubishi S490 User Manual Page 2

Comments to this Manuals

Related products and manuals for Data projectors Mitsubishi S490