VIDEO COPY PROCESSORMODELP91WP91EOPERATION MANUALTHIS OPERATION MANUAL IS IMPORTANT TO YOU.PLEASE READ IT BEFORE USING YOUR VIDEO COPY PROCESSOR.V
74INSTALLATION OF PAPERMoisture, fingerprints or dust on thepaper surface may cause a noise atprinting or deterioration in printquality. Set the paper
8Do not use the bent or wrinkledpaper.When the paper is fed out skewedfrom the print exit, adjust the paperposition so that it is fed out straight.Whe
9 5EXAMPLE OF CONNECTION / SETTING OF SWITCHESConnecting to various composite video signal equipments suchas medical equipment.1 Turn off the power sw
10For the functions of the MODE switch, refer to "MODE SWITCHFUNCTIONS" on page 21 - 23. Medical Video Signal1 Turn off the power switches o
116PRINTING Printing Procedure• Display a picture tobe printed on themonitor screen, andpress the " PRINT "button.When printing isover, a bu
12 Use of Remote ControlConnect the wired remote control tothe remote control terminal on therear panel.Press the remote control button toprint pictur
13 Adjustment of Brightness/ContrastYou can adjust brightness and contrast of print whileobserving the monitor screen.7ADJUSTMENT OF PRINT PICTURE Con
142 Store the set value.OPEN BRT CONTGAMMAPRT-SIZECOPY/FEEDPRINTPRINTA value is stored by pressing "PRINT"button.A stored value will not be
15 Releasing ABC modeHold down the print size button " " for approx. 3 seconds.A tone is given, LED display changes from to and ABC mode
16You can select print size by pressing the print-size button" ". Each time the button is pressed,the indicator and print size is switcheda
WARNING:Use the AC power cord recommended as below and the included composite video cable soas not to interfere with radio and television reception.If
17 Locking the settingsYou can lock the setting of each button on the front panel(BRT, CONT, PRT-SIZE, GAMMA) .8SPECIAL FUNCTION Locking the setting (
18 Printing the set conditionsYou can print the set conditions of BRT, CONT and GAMMAunder the image.1 Turn on the power.• Press the "POWER"
19When an error in operation occurs it is warned by an audiblealarm and a visible error display in the LED indicator.9ERROR DISPLAYCause/Error display
20Cause/Error displaySymptom/ RemedySymptom/ Remedy[Symptom]• When the door opens, an alarm tone is given.Cause/Error display[Remedy]Close the door.[S
21MODE SWITCH(DIP switch)Functions1 IMP(IMPEDANCE)75Ω/HIGHUsually set to "75Ω".Set to "HIGH" when making branch connection of a mo
22MODE SWITCH(DIP switch)Functions5 AFCON/OFFUsually set to "OFF".Set to "ON" when connecting equipment with a poor signal.Picture
23MODE SWITCH(DIP switch)Functions9 SAVING(PAPER SAVING)ON/OFFSet this switch to select the margin size.ON: Printed with narrow margin.OFF: Printed wi
24LeftPoint andrightPower offExcept small sizeSet state/ModePower offThroughThroughContents of rightside LED displayVideooutputSmall sizefor 1st image
25When the thermal head is dirty with dust and perspiration, etc., white spots or stripes mayappear on the print. In this case, clean the thermal hea
26Turn off the power for maintenance.Wipe off stains of the front panel with a soft cloth.When the panel is heavily stained, wipe off with the clothmo
The lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of uninsulated "dangerous
27SERVICE INFORMATIONBefore requesting service please review this operation manual to correct minor complaints.If you are unable to correct the proble
MITSUBISHI ELECTRONICS AMERICA, INC.5665 PLAZA DRIVE P.O. BOX 6007CYPRESS, CA 90630-0007, USAPhone (714)220-2500 FAX (714)236-6339Made from recycle
111111 CONTENTS ... 122222 PRECAUTIONS ...
22PRECAUTIONSMAINTAIN GOOD VENTILATIONVentilation slots and holes are provided on sides of thisunit.Place the unit on a hard and level surface and loc
3FOR LONG OPERATING LIFEUNSUITABLE MATERIALS FOR THE UNITMany plastic components are used in the back-side.Coat flaking and deformation are likely to
4SAFETY TECHNICAL CHECKSPeriods: According to the recommendations of the manufacturer of medical device.Scope: a) Visual checkHousing, cables, operato
5 3FEATURES AND FUNCTIONSOPEN BRT CONTGAMMAPRT-SIZECOPY/FEEDPRINTA1 Front Panel 11Power switch Turns on/off the power.13FunctionNameReferencePage2P
6 Rear Panel POTENTIAL EQUALIZATION TERMINAL This is used to equalize the potential of the equipmentconnected to this unit.For d
Comments to this Manuals