Mitsubishi MOTION CONTROLLERS Q172DCPU Instruction Manual Page 166
- Page / 316
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
7 - 19
7 TRANSMISSION MODULE
(g) When the mode setting device becomes "3", the clutch status turns OFF,
while the clutch ON/OFF command device is OFF and the clutch status is
ON.
3
OFF
Clutch status
Drive module current
value
Clutch ON/OFF
command device
(Note)
Mode setting device
value
(Note) : Refer to Section "7.2.2 Parameters" for details.
OFF
ON
(h) When the mode setting device is changed from "except 3" to "4", the clutch
status turns off regardless of the clutch ON/OFF command device.
(i) When the clutch ON/OFF address setting device data is changed during the
clutch processing of one-shot mode, it becomes valid by turning the next
clutch ON/OFF command device off to on.
(j) When the drive module stops during the clutch ON/OFF processing by
turning the clutch ON/OFF command device on, or if the clutch ON/OFF
command device is turned on though the drive module stops, the one-shot
mode clutch does not end until the travel value condition set to the setting
travel value before clutch ON or setting travel value after clutch ON is
satisfied.
(k) When the current value change is made to the drive module during the
clutch ON/OFF processing by turning the clutch ON/OFF command device
on, the clutch turns off at the position where the setting travel value before
clutch ON or setting travel value after clutch ON from the clutch ON position
is satisfied.
- Q173DCPU 1
- Q172DCPU 1
- SAFETY PRECAUTIONS 2
- For Safe Operations 3
- 2. For fire prevention 3
- 3. For injury prevention 4
- 4. Various precautions 4
- (4) Wiring 8
- (6) Usage methods 9
- Electro 10
- (10) General cautions 11
- 1. OVERVIEW 18
- (Note-2) : SSCNET: S 19
- 1 OVERVIEW 20
- 2.1 Starting Up the System 22
- MT Developer 23
- Real mode 24
- Virtual mode 24
- 2.3.3 Servo programs 27
- : Used, : Unusable 28
- (1) Internal signals 32
- (2) External signals 32
- 4.1 Internal Relays 34
- (1) Internal relay list 34
- (8) Common device list 41
- 4.1.1 Axis statuses 45
- (8) RLS signal (M2412+20n) 48
- ..….... Command signal 53
- .......…….. Status signal 57
- ...…... Command signal 64
- 4.1.7 Common devices 68
- "0" 70
- .....…..….. Status signal 78
- 4.2 Data Registers 82
- (1) Data register list 82
- (7) Common device list 89
- Feed current value 93
- execution 101
- .......... Command signal 102
- 4.3 Motion registers (#) 104
- 4.5 Special registers (SD) 109
- System Settings 111
- Mounted Not mounted 111
- Unused 0 is stored 111
- Servo amplifier 111
- ........... Monitor device 112
- Faulty SSCNET No 113
- 0 : SSCNET 1 113
- 1 : SSCNET 2 113
- .........….. Monitor device 115
- ..……..…… Command device 115
- 5. MECHANICAL SYSTEM PROGRAM 116
- (1) Block 118
- (2) System 118
- 5.2 Mechanical Module List 120
- 6. DRIVE MODULE 122
- 6 DRIVE MODULE 123
- (Note-3) 124
- (Note-1) 125
- 6.1.2 Parameter list 132
- CAUTION 138
- 6.2.2 Parameter list 142
- (2) Current value change 145
- 7. TRANSMISSION MODULE 148
- Q173DCPU Q172DCPU 149
- (Note-2) 150
- 7 TRANSMISSION MODULE 151
- (1) Gear ratio 151
- 7.2 Clutch 152
- VA, VB : Drive module speed 153
- 7.2.1 Operation 158
- (1) ON/OFF mode 158
- (2) Address mode 159
- (3) Address mode 2 161
- (Note-2) 163
- (5) External input mode 168
- 7.2.2 Parameters 172
- (Note-1), (Note-2) 174
- (Note-3), (Note-4) 174
- (Note-3) 175
- 7.3 Speed Change Gear 181
- 7.3.1 Operation 181
- (Note-1) 182
- Ball screw 186
- Rotary table 186
- 8 OUTPUT MODULE 188
- 8.1 Rollers 190
- 8.1.1 Operation 190
- (1) Operation 190
- (2) Control details 191
- 8.1.2 Parameter list 191
- (1) Output unit 191
- Number of pulses per roller 192
- Roller diameter (L) 192
- Speed limit value 193
- Drive module 194
- Gear(Gear ratio) 194
- Ball screw pitch (P) 195
- Number of pulses per ball 195
- 8.3 Rotary Tables 198
- 8.3.1 Operation 198
- 8.4 Cam 206
- (5) Control details 209
- (6) Control change 209
- (7) Program example 210
- (1) Cam No 211
- (2) Resolution 211
- (4) Operation mode 211
- (5) Cam data table 213
- Number of pulses per cam 215
- (4) Output unit 216
- C-1) [PLS] 219
- C-1) [PLS] in the 219
- 8.4.4 Cam curve list 224
- (1) Parameter list 225
- (2) Operating method 227
- OFF ON even if 1 axis 232
- 9.4 Stop and re-start 236
- (1) Virtual axis stop 236
- <Real mode> 240
- <Virtual mode> 240
- [Real Mode Axis Setting] menu 241
- APPENDIX 1 Cam Curves 246
- PPENDICES 247
- APP - 22 267
- 1 293
- WARRANTY 313
- MOTION CONTROLLER Qseries 314
- (Q173DCPU/Q172DCPU) 314
- MITSUBISHI ELECTRIC 316
Related products and manuals for Security access control systems Mitsubishi MOTION CONTROLLERS Q172DCPU
(174 pages)
(90 pages)Philips DLA1258D-27 manuály
Uživatelské manuály a uživatelské příručky pro Příslušenství pro video Philips DLA1258D-27.
Poskytujeme 1 manuály pdf Philips DLA1258D-27 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals