Mitsubishi PLA-RP Service Manual Page 65
- Page / 86
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
65
123456
ON
OFF
123456
ON
OFF
12
3
456
ON
OFF
123456
ON
OFF
A-Control Service Tool SW2 setting
Temperature display of indoor liquid pipe
Indoor 1
Temperature display of indoor liquid pipe
Indoor 2
Temperature display of indoor condenser/
evaporator pipe Indoor 1
Temperature display of indoor condenser/
evaporator pipe Indoor 2
Error Code
Meaning of error code and detection method
Case
Judgment and action
P6
Freezing/overheating protection is
working
1 Freezing protection (Cooling mode)
The unit is in six-minute resume prevention
mode if pipe <liquid or condenser/evap-
orator> temperature stays under
-15: for three minutes, three minutes
after the compressor started. Abnormal
if it stays under -15: for three minutes
again within 16 minutes after six-minute
resume prevention mode.
2 Overheating protection (Heating mode)
The units is in six-minute resume
prevention mode if pipe <condenser /
evaporator> temperature is detected as
over 74: after the compressor started.
Abnormal if the temperature of over
74: is detected again within 10 minutes
after six-minute resume prevention
mode.
P8
1 Slight temperature difference
between indoor room
temperature and pipe <liquid
or condenser / evaporator>
temperature thermistor
• Shortage of refrigerant
• Disconnected holder of pipe
<liquid or condenser /
evaporator> thermistor
• Defective refrigerant circuit
2 Converse connection of
extension pipe (on plural units
connection)
3 Converse wiring of indoor/
outdoor unit connecting wire
(on plural units connection)
4 Defective detection of indoor
room temperature and pipe
<condenser / evaporator>
temperature thermistor
5 Stop valve is not opened
completely.
(Cooling or drying mode)
1 Clogged filter (reduced airflow)
2 Short cycle of air path
3 Low-load (low temperature)
operation beyond the tolerance
range
4 Defective indoor fan motor
• Fan motor is defective.
• Indoor controller board is
defective.
5 Overcharge of refrigerant
6 Defective refrigerant circuit
(clogs)
(Heating mode)
1 Clogged filter (reduced airflow)
2 Short cycle of air path
3 Over-load (high temperature)
operation beyond the tolerance
range
4 Defective indoor fan motor
• Fan motor is defective.
• Indoor controller board is
defective.
5 Overcharge of refrigerant
6 Defective refrigerant circuit
(clogs)
7 Bypass circuit of outdoor unit
is defective.
(Cooling or drying mode)
1 Check clogs of the filter.
2 Remove shields.
4 Measure the resistance of fan motor's winding.
Measure the output voltage of fan's connector
(FAN) on the indoor controller board.
WThe indoor controller board should be
normal when voltage of AC 100~240V is
detected while fan motor is connected.
Refer to 10-6-2.
56 Check operating condition of refrigerant
circuit.
(Heating mode)
1 Check clogs of the filter.
2 Remove shields.
4 Measure the resistance of fan motor's
winding.
Measure the output voltage of fan's connector
(FAN) on the indoor controller board.
WThe indoor controller board should be
normal when voltage of AC 100~240V is
detected while fan motor is connected.
Refer to 10-6-2.
5~7Check operating condition of refrigerant
circuit.
Abnormality of pipe temperature
<Cooling mode>
Detected as abnormal when the pipe tem-
perature is not in the cooling range 3 min-
utes later of compressor start and 6 min-
utes later of the liquid or condenser/evapo-
rator pipe is out of cooling range.
Note 1) It takes at least 9 min. to detect.
Note 2) Abnormality P8 is not detected in
drying mode.
Cooling range : Indoor pipe temperature
(TH2 or TH5) – intake temperature
(TH1) [ -3 deg
TH: Lower temperature between: liquid
pipe temperature and condenser/
evaporator temperature
<Heating mode>
When 10 seconds have passed after the
compressor starts operation and the hot
adjustment mode has finished, the unit is
detected as abnormal when
condenser/evaporator pipe temperature is
not in heating range within 20 minutes.
Note 3) It takes at least 27 minutes to
detect abnormality.
Note 4) It excludes the period of defrosting
(Detection restarts when defrosting
mode is over)
Heating range : 3 deg [ (Condenser/
Evaporator temperature(TH5) –
intake temperature(TH1))
1~4 Check pipe <liquid or condenser /
evaporator> temperature with room
temperature display on remote
controller and outdoor controller circuit
board.
Pipe <liquid or condenser / evaporator>
temperature display is indicated by
setting SW2 of outdoor controller circuit
board as follows.
23Check converse connection of extension
pipe or converse wiring of indoor/outdoor
unit connecting wire.
Conduct temperature check with outdoor
controller circuit board after connecting
‘A-Control Service Tool(PAC-SK52ST)’.
(
)
OC297-E-3.qxp 05.5.6 5:35 PM Page 65
- MODEL SELECT 1
- TEST RUN 1
- TECHNICAL CHANGES 2
- SAFETY PRECAUTION 4
- [3] Service tools 5
- [1] Cautions for service 6
- Gravimeter 7
- PART NAMES AND FUNCTIONS 8
- ● Display 9
- SET TEMPERATURE display 9
- ON/OFF TEMP 10
- SPECIFICATIONS 11
- 1.UK / PUH-P1.6YGAA1.UK 15
- 1.UK / PUH-P2YGAA1.UK 15
- 1.UK / PUH-P3YGAA1.UK 16
- 1.UK / PUH-P2.5YGAA1.UK 16
- 1.UK / PUH-P4YGAA1.UK 17
- 1.UK / PU-P2.5YGAA1.UK 19
- 1.UK / PU-P1.6YGAA1.UK 19
- 1.UK / PU-P2YGAA1.UK 19
- 1.UK / PU-P3YGAA1.UK 20
- 1.UK / PU-P4YGAA1.UK 20
- 6-1-1. COOLING CAPACITY (1) 21
- COOLING CAPACITY (2) 22
- PLA-RP2AA.UK / PUHZ-RP2VHA 23
- PUHZ-RP2.5VHA 25
- PUHZ-RP3VHA 27
- PUHZ-RP4VHA 29
- PUHZ-RP5VHA 31
- PUHZ-RP6VHA 33
- COOLING CAPACITY (15) 35
- COOLING CAPACITY (16) 36
- COOLING CAPACITY (17) 37
- COOLING CAPACITY (18) 38
- COOLING CAPACITY (19) 39
- COOLING CAPACITY (20) 40
- COOLING CAPACITY (21) 41
- COOLING CAPACITY (22) 42
- COOLING CAPACITY (23) 43
- COOLING CAPACITY (24) 44
- COOLING CAPACITY (25) 45
- COOLING CAPACITY (26) 46
- COOLING CAPACITY (27) 47
- COOLING CAPACITY (28) 48
- 1.UK PUH-P•YGAA1.UK 49
- D.B.(°C) 50
- OUTDOOR W.B.(°C) 50
- PUH-P•VGAA1.UK PUH-P•YGAA1.UK 51
- PU-P•VGAA.UK PU-P•YGAA.UK 51
- PU-P•VGAA1.UK PU-P•YGAA1.UK 51
- 6-4. STANDARD OPERATION DATA 52
- Heat pump type (2) 54
- Cooling only type (3) 56
- BAND CENTER FREQUENCIES, Hz 58
- PLA-RP5AA.UK 59
- PLA-RP5AA 59
- PLA-RP6AA.UK 59
- PLA-RP6AA1.UK 59
- OUTLINES AND DIMENSIONS 60
- WIRING DIAGRAM 61
- REFRIGERANT SYSTEM DIAGRAM 62
- TROUBLESHOOTING 63
- 10-4. EMERGENCY OPERATION 68
- Vane motor 69
- Drain pump 69
- Drain sensor 69
- Fan motor 69
- 0=15k' ±3% 70
- 0=6.0k' ±5% 70
- 10-6. TEST POINT DIAGRAM 71
- DISASSEMBLY PROCEDURE11 74
- OPERATING PROCEDURE 75
- PHOTOS & ILLUSTRATIONS 75
- 12 PARTS LIST 77
- No. Parts No. Parts Name 81
- OPTIONAL PARTS 84
Related products and manuals for Split-system air conditioners Mitsubishi PLA-RP
(6 pages)
(21 pages)
(69 pages)© 2020, manymanuals.com. All rights reserved. | 0.140 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals