Mitsubishi PLA-RP Installation Manual

Air-ConditionersPLA-RP·BAINSTALLATION MANUALFor safe and correct use, read this manual and the outdoor unit installation manual thoroughly before inst

105) Assigning a remote controller to each unit (Fig. 6-8)Each unit can be operated only by the assigned remote controller.Make sure each pair of an

116. Electrical workModePower failure automatic recoveryIndoor temperature detectingLOSSNAY connectivityPower voltageSettingsNot availableAvailable *1

12Changes the selection(No.). Unit No. "1-4"Refrigerant address No. "00-15"Outlet No."1-4"or "0"Up/Down air di

13As for this air conditioner, air conditioner No. is "unit No. 1" ofrefrigerant address "0".Flow of procedureRefrigerantaddressNo

147. Test runON/OFF TEMPFANVANETEST RUNAUTO STOPAUTO STARThminLOUVERMODECHECKRESETSET CLOCKTEST RUNFig. 7-2Fig. 7-1,°C°CSIMPLEPAR-21MAAON/OFFFILTERC

157. Test runOPERATION INDICATOR lamp blinking patternBeep Beep Beep Beep Beep Beep BeepOffApprox. 2.5 sec.OnApprox. 3 sec.On0.5 sec.On0.5 sec.On0.5 s

167. Test runWater supply pumpWater (about 1000cc)Drain plugPour water through outlet.Be carefule not to spray water into the drain pump mechanism.7.

179.1. Checking the contents (Fig. 9-1)• This kit contains this manual and the following parts.Accessory name Q’ty RemarksGrille 1 950 × 950 (mm)Scr

189. Installing the grilleFig. 9-6CeilingMain unitGrilleMake sure that there are no gapsAdjust the nut of the main unitusing a wrench, etc.Fig. 9-7Fi

19(1) Press the TEST button for three seconds toactivate the maintenance mode.(2) Press the TEMP. buttons to set the refrigerant address.MAINTENANCE(

2Contents1. Safety precautions ...22. Installation location ...

RG79D251K01_CS_0228.indd Sec1:38RG79D251K01_CS_0228.indd Sec1:38 28/02/2007 12:43:3428/02/2007 12:43:34

RG79D251K01_CS_0228.indd Sec1:39RG79D251K01_CS_0228.indd Sec1:39 28/02/2007 12:43:3428/02/2007 12:43:34

Please be sure to put the contact address/telephone number on this manual before handing it to the customer.• Low Voltage Directive 2006/95/EC• Elect

32. Installation locationRefer to the outdoor unit installation manual.3. Installing the indoor unitFig. 3-1Fig. 3-2Fig. 3-315016016016016090860-9102

43. Installing the indoor unit3.5. Suspension structure (Give site of suspension strong structure) (Fig. 3-5)• The ceiling work differs according to

54. Installing the refrigerant piping4.1. Precautions For devices that use R410A refrigerant• Use ester oil, ether oil or alkylbenzene oil (small am

64.3. Indoor unit (Fig. 4-3)Heat insulation for refrigerant pipes:1 Wrap the enclosed large-sized pipe cover around the gas pipe, making sure that t

76. Electrical work6.1. Indoor unit (Fig. 6-1)1. Remove the electrical wiring service panel.2. Remove the electrical box cover.3. Wire the power c

8S1S2S3LNBLUEBLUEYELLOWYELLOWCN01CN01BLACKCN01BLACKS1S2S3LNYELLOWBLUEBLUEYELLOWCN016. Electrical work6.1.2. Separate indoor unit/outdoor unit power s

96. Electrical work6.2. Remote controller6.2.1. For wired remote controller1) Installing procedures(1) Select an installing position for the remote c