Mitsubishi PLA-RP Installation Manual download pdf (Page 13)

As for this air conditioner,

air conditioner No. is "unit No. 1" of

refrigerant address "0".

Flow of procedure

Refrigerant

address

No."00"

Refrigerant

address

No."01"

Unit No."1" Unit No."1"Unit No."2" Unit No."2"

Remote controller

Check from refrigerant address 00 at first.

Change to unit No.1 and check

Change to unit No.2 and check

Change to unit No.3 and check

Change to unit No.4 and check

Change to unit No.1 and check

Change to unit No.2 and check

Change to unit No.3 and check

Change to unit No.4 and check

Change to unit No.1 and check

Change to unit No.2 and check

Change to unit No.3 and check

Change to unit No.4 and check

Change to unit No.1 and check

Change to unit No.2 and check

Change to unit No.3 and check

Change to unit No.4 and check

When "Err" is displayed, refrigerant address

does not have further "unit No.".

Change to the next "refrigerant address No..

(Refrigerant No "00"~max. No."15")

[1] To check refrigerant address No. and unit No.

1.Press Mode button (Return button)

and unit No. or refrigerant

address No. blinks.

Adjust refrigerant address No.to "00" and unit No."1" with Set

Temperature button

2.Press Filter

button to send the information on remote controller.

3. Wait for 15 seconds. How does the air conditioner run?

Only air from the outlet of which No. displayed on remote controller

blows downward.

Refrigerant address No.00 and unit No.1 are the air conditioner No..

All outlets are closed.

Go to step [2].

[2] To check by changing unit No. one after the other

(Maximum unit No. is 4)

1.Press Mode button (Return button)

and unit No. blinks.

Outlet No.

Up/Down air direction

Refrigerant addres No.

Unit No.

Outlet No.

Up/Down air direction

Refrigerant addres No.

Unit No.

Adjust to the next unit No.with Set Temperature button

(refrigerant address No.00 is remained.)

2. Press Filter

button

to send the information on remote controller.

3. Wait for 15 seconds . How does the air conditioner run?

Only air from the outlet which No. displayed on remote controller blows

downward.

No. displayed on remote controller is air conditioner No.. (Checking

completed)

All outlets are closed.

Repeat [1] and check. (If all the numbers are checked up to No.4

and is not found, go to [3].)

"Err" is displayed on remote controller.

The refrigerant address does not have further unit No.. (Go to [3].)

[3] To check Unit No. of following refrigerant address No.(Maxmum

refrigerant address No. is 15)

1.Press Mode button (Return button)

to blink refrigerant address No..

Adjust refrigerant No. with Set Temperature button .

* By changing refrigerant address, unit No. and outlet No. turn to initial

display.

2.Go back to [2] and check Unit No. again from Unit No. 1 in order.

To clear ﬁ xed setting

To clear all ﬁ xed setting(reset to factory default), press check button(clear

botton)

for more than 3 seconds in ﬁ xed airﬂ ow direction mode.

Display of remote controller blinks and the set information is cleared.

Note: This operation clears the fixed setting information of all air

conditioner connected to the remote controller.

Err

Outlet No.

Up/Down air direction

Refrigerant addres No.

Unit No.

Each air conditioner has its own refrigerant address No. and unit No.

(Example below).

To ﬁ nd air conditioner No. to set, refer to the procedures below.

Air conditioner No. is found by its airflow direction with the unit No.

changed one after the other.

How to ﬁ nd air conditioner No.

6. Electrical work

RG79D251K01_EN_0227.indd 13RG79D251K01_EN_0227.indd 13 28/02/2007 09:49:0028/02/2007 09:49:00

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 21 22

Comments to this Manuals

No comments

Mitsubishi PLA-RP Installation Manual Page 13

Comments to this Manuals

Related products and manuals for Split-system air conditioners Mitsubishi PLA-RP