Mitsubishi 20-MYA Specifications Page 8
- Page / 116
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
- 6-
TYPICAL INSTALLATION EXAMPLE
MECHANICAL SPECIFICATIONS
General
All units are factory assembled, piped, internally wired.
They are also tested and checked under a strict quality
control system in the factory.
Exterior surfaces of all units of outdoor unit are
phosphatized, zinc-coated steel with powder coating
and ivory white baked enamel finish.
Refrigeration Controls
Refrigeration controls include condenser fan,
evaporator fan and compressor contactors.
Compressors
All units have high efficiency type hermetic line starting
compressors.
Compressors are equipped with thermal overload
protector, over-current relay and high pressure
protection control.
Crankcase heaters are standard.
Evaporator Coils
Highly efficient cross-finned coil are applied to provide a
larger cooling capacity with low air speed on the coil.
Coils are made of 9.52mm OD and 0.35mm thick
seamless copper tubing mechanically bonded to 0.12mm
thick aluminium fins and are factory leak tested at a
pressure of 3.3MPa. They are provided with strainers
attached to the capillary tubes to further ensure a clean
system.
Condenser Coils
Unnecessary power input due to higher discharge
pressure is avoided by high performance designs of
cross-finned coil.
Condenser coils are made of 9.52mm OD, 0.35mm
thick seamless copper tubes mechanically bonded to
0.12mm thick aluminium fins and factory pressure
and leak tested at 3.3MPa.
Evaporator Fans
The sirocco fans are made of galvanized steel or plastic
and balanced to proved accurate air flow performance
at low noise level.
Condenser Fan
The direct-drive propeller fan is dynamically balanced,
to ensure smooth airflow.
A weatherproof three-phase squirrel cage induction
motor is used to drive the condenser fan.
PU(H)
PE(H)
PE(H)
PU(H)
- DATA BOOK 1
- SPECIFICATION GUIDELINES -113 3
- SAFETY FOR USE 4
- A COMPLETE LINE UP 6
- FEATURES 7
- DESCRIPTIONS 7
- TYPICAL INSTALLATION EXAMPLE 8
- MECHANICAL SPECIFICATIONS 8
- MODEL-DESIGNATION BREAKDOWN 9
- PE-10 MYC 9
- SPECIFICATIONS 10
- PEH-5,7,8MYA 11
- Heat pump 11
- PEH-10,15,20MYA 12
- ELECTRICAL DATA 13
- PEH-5,7,8MYA-EU 14
- PEH-10,15,20MYA-EU 16
- SELECTION PROCEDURE 18
- Factor for Various Air Flow 19
- CAPACITY TABLES 20
- Heating Capacity 21
- (Standard Air Flow) 21
- (PEH only) 39
- FAN PERFORMANCE 40
- PE-15MYC1-EU 41
- PEH-15MYA-EU 41
- PE-20MYC-EU 41
- PEH-20MYA-EU 41
- (1) Shape of belt groove 42
- SOUND DATA 43
- OUTLINE DIMENSIONS 45
- PE(H)-10 46
- PE(H)-15 46
- PE(H)-20 47
- PU(H)-7,8,10 48
- (Upper blow) 48
- PUH-8,10 49
- (Side blow) 49
- PUH-15,20 50
- PAC-204RC 52
- Attach the accessory 53
- LOW AMBIENT 64
- COOLING PARTS 64
- MF1 Note 65
- PE-15MYC1-EU PE-20MYC-EU 66
- PEH-15,20MYA-EU 67
- REFRIGERANT SCHEMATICS 68
- SAFETY & CONTROL DEVICES 69
- PEH-7,8,10MYA-EU 70
- SPECIAL ORDER 71
- PHYSICAL DATA 72
- [INDOOR AIR CIRCUIT] 73
- [EVAPORATOR] 73
- [OUTDOOR AIR CIRCUIT] 73
- [CONDENSER] 73
- [ENCLOSURE AND FRAME] 74
- 2-EU PUH-10MYE1-EU 78
- INSTALLATION 81
- PU(H)-7,8, 10 (Upper blow) 82
- (1) At a single installation 83
- Indoor unit 84
- 3. Installation of the unit 85
- Outdoor unit 85
- Duct construction 86
- Lifting method 86
- Piping connection 87
- Refrigerant piping 88
- Airtight test 89
- Evacuation 89
- Additional refrigerant charge 89
- Drain piping 90
- Electric wiring 91
- Upper blow 92
- PE(H)-7:Single phase 93
- Refer to (3)-4 94
- Refer to (3)-3 94
- Refer to (3)-5 94
- (Not change) 95
- Detail section A 96
- LCD remote controller inside 96
- Check items 97
- Obstacle blocking air inlet 98
- 2. Caution for use 99
- 3. Maintenance 99
- Flexion load (W) 100
- 1.4 kg 2.2kg 100
- V pulley 100
- 9. Troubleshooting 102
- HOW TO OPERATE 103
- 2. Selecting operation 104
- 4. Time setting 105
- 5. Other function 105
- 1. Outline 106
- 3. Parts 106
- 2. Caution 106
- 4. Installation 107
- 4-2. PUH-15,20 108
- 4-3-1. Install 109
- 4-3-2. Wiring 109
- Confirmation 110
- Fan controller layout 110
- 6. Troubleshooting 111
- Thyristor module 114
- SPECIFICATION GUIDELINES 115
- DATA BOOK PE,PEH 116
Related products and manuals for Split-system air conditioners Mitsubishi 20-MYA
(26 pages)
(20 pages)
(13 pages)
(20 pages)© 2020, manymanuals.com. All rights reserved. | 3.678 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals