Mitsubishi PUHZ-RP60VHA Service Manual Page 128
- Page / 178
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
128
3. How to start "Judgment of refrigerant leakage " mode.
To know the current condition of refrigerant amount, same operation must be performed.
Please repeat the same procedure 1~3 as when "Initial learning operation" for "Checking operation".
4Press CLOCK button and select the [GAS LEAK JUDGE]
5Press ( ) button to confirm. (Display A LOADING)
Display[C] indication Meaning (% setting : 80%,RP60-RP140)
" 0 " Refrigerant leakage is less than 20% of initial condition.
" 20 " Refrigerant leakage is more than 20% of initial condition.
" 8888 " "Error"=No initial data is available.
<Note>
% for judgment can be changed by "Unit function setting of remote controller".
RP35-RP50 : Selectable either 70%(initial setting) or 50%
RP60-RP140 : Selectable either 80%(initial setting) or 60%
Refer to 12-1 Mode No.21.
(When the "%" for judgment is changed, please start "Initial learning 1~3" about 1 minute (3)and cancel 4'.)
Then, please start "Judgment of refrigerant leakage" mode(1~5).
<H ow to reset the initial condition (data) >
When the unit is removed and installed again or refrigerant is changed additionally, the "Initial learning" must be
performed again by following procedure.
(1)Turn "Main Power" OFF.
(2)Connect the pin of CN31 to ON position on the outdoor controller board.
(3)Turn SW4-1 on the outdoor controller board to ON.
(4)Turn "Main Power" ON to reset the initial data.
After reset the data, please turn the pin of CN31 and SW4-1 to original(OFF) position.
<Caution>
1.On the following condition, the operation cannot be stabillized and judgment of cheking operation may not be accurate.
(a)Outdoor temperature ] 40:or Room temperature [ 23:
(b)Airflow setting is not "High-notch".
2.Please check the operation and unit status, when the operation is not stabilized after more than 45 minutes.
w
GAS LEAK
TEST START
GAS LEAK
JUDGE
Refrigerant leakage
detection judgment
Refrigerant leakage
detection
(initial teaching)
FILTER
Display
C
Waiting for response
Flashing
Loading
Judgment
" 0"
OC374C--5.qxp 08.2.22 8:12 AM Page 128
- SERVICE MANUAL 1
- [Service Ref.] 2
- 1 TECHNICAL CHANGES 3
- REFERENCE MANUAL 4
- 3 SAFETY PRECAUTION 5
- Gravimeter 6
- [3] Service tools 6
- (1) which 7
- Dimension A 8
- Dimension B 8
- 4 FEATURES 9
- 5 SPECIFICATIONS 10
- 1PUHZ-RP125YHA21 12
- 1 / YHA3 12
- 1:135(298) / YHA3:130(287) 12
- (at 20°C) 13
- 6-3. NOISE CRITERION CURVES 14
- 7 OUTLINES AND DIMENSIONS 20
- Unit : mm 21
- Piping Knockout Hole Details 22
- Example of Notes 22
- Over 150mm 23
- Over 1000mm 23
- M-NET ADAPTER 25
- (w1 MODEL SELECT) 30
- (Contact Input)> 31
- 9 WIRING SPECIFICATIONS 32
- Set the SW8-3 to ON 33
- 1 2 (SW8) 33
- 9-4. M-NET WIRING METHOD 35
- 9-4-1. M-NET address setting 36
- 10 REFRIGERANT SYSTEM DIAGRAM 37
- 11 TROUBLESHOOTING 40
- OUTDOOR BOARD LED Display 41
- 1, L2, L3 and 41
- Error code (2 or 4 digits) 43
- (Alternating Display) 43
- [Procedure] 45
- Beep Beep 46
- 1,100VHA3) 51
- •V•W phase) to com 51
- 1, RP100VHA3) 51
- •V•W phase) to 51
- •V•W phase) to compres 52
- Continued to the next page 55
- From the previous page 56
- • Before repair 63
- 11-6. HOW TO CHECK THE PARTS 67
- PUHZ-RP35/50/60/71/100VHA2 67
- PUHZ-RP35/50/60/71/100VHA3 67
- DC DC250~330V 68
- CC DC15V 68
- Linear expansion valve 70
- (RP35-RP71) 70
- (RP100-RP140) 71
- <Composition> 72
- 11-8. EMERGENCY OPERATION 74
- 11-9. TEST POINT DIAGRAM 76
- PUHZ-RP35VHA21 PUHZ-RP35VHA3 79
- PUHZ-RP50VHA21 PUHZ-RP50VHA3 79
- PUHZ-RP60VHA2 80
- PUHZ-RP71VHA2 80
- PUHZ-RP71VHA21 PUHZ-RP71VHA3 81
- PUHZ-RP60VHA21 PUHZ-RP60VHA3 81
- PUHZ-RP100VHA2 82
- PUHZ-RP125VHA2 82
- PUHZ-RP140VHA2 82
- PUHZ-RP100VHA21 83
- PUHZ-RP125VHA21 83
- PUHZ-RP140VHA21 83
- PUHZ-RP100YHA2 84
- PUHZ-RP125YHA2 84
- PUHZ-RP140YHA2 84
- PUHZ-RP100YHA21 85
- PUHZ-RP125YHA21 85
- PUHZ-RP140YHA21 85
- Outdoor power circuit board 86
- ➔ Transmitting signal 87
- Active filter module 91
- (1) Function of switches 93
- Model select 94
- Power consumption 95
- (SW1 on) 95
- Detailed 96
- 1 second 98
- SW2 setting 100
- Display detail 100
- Explanation for display Unit 100
- •The ones digit 106
- 12 FUNCTION SETTING 107
- Temperature correction: Valid 108
- Mode number 109
- Setting number 109
- [Operating Procedure] 110
- TEST RUN 111
- Hold down the 113
- 13-2. REQUEST CODE LIST 115
- Refer to 118
- 14 EASY MAINTENANCE FUNCTION 124
- Display 125
- Check Points 126
- Stabilized 127
- " 0" 128
- 15 DISASSEMBLY PROCEDURE 129
- OPERATING PROCEDURE PHOTOS 130
- OPERATING PROCEDURE 134
- PHOTOS & ILLUSTRATION 134
- PUHZ-RP60,71VHA2(1)/VHA3 134
- (1)(TH33 : See Photo 9.) 135
- 1 PUHZ-RP60/71VHA3 135
- PUHZ-RP100, 125, 140VHA2(1) 139
- PUHZ-RP100VHA3 139
- 1 PUHZ-RP100VHA3 140
- PUHZ-RP100/125/140YHA2(1) 144
- PUHZ-RP100YHA3 144
- 1 PUHZ-RP100YHA3 146
- PUHZ-RP35VHA2 155
- PUHZ-RP50VHA2 155
- 17 RoHS PARTS LIST 162
- 1 PUHZ-RP35VHA3 174
- 1 PUHZ-RP50VHA3 174
- (1) VHA3 175
Related products and manuals for Split-system air conditioners Mitsubishi PUHZ-RP60VHA
(14 pages)
(104 pages)© 2020, manymanuals.com. All rights reserved. | 0.201 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals