Mitsubishi FR-S500 Instruction Manual Page 104
- Page / 191
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
95
2
(1) How to make a restart after a stop by the
STOP
RESET
key input from the
operation panel (Restarting method with
shown)
1) After completion of deceleration to
a stop, switch off the STF or STR
signal.
2) Press the
PU
EXT
key to
show
PU
. ........( canceled)
3) Press the
PU
EXT
key to return to
EXT
.
4) Switch on the STF or STR signal.
Speed
Time
key
Stop and restart example for external operation
Control panel
key
PU
EXT
STOP
RESET
STF ON
(STR) OFF
REMARKS
• By entering the reset signal (RES) during operation, the inverter shuts off its
output while it is reset, the internal thermal summation value of the electronic
overcurrent protection and the number of retries are reset, and the motor coasts.
• The Pr. 75 value can be set any time. Also, if parameter (all) clear is executed,
this setting will not return to the initial value.
• When the inverter is stopped by the PU stop function, the display alternates
between
and
. An alarm is not output.
(2) How to make a restart when a stop is made by the
STOP
RESET
key
input from the PU
1) After completion of deceleration
to a stop, switch off the STF or
STR signal.
2) Press the
EXT
key
. .....................(
canceled)
3) Switch on the STF or STR signal.
Time
key
key
STOP
RESET
EXT
Speed
Control panel
STF ON
(STR) OFF
Stop and restart example for external operation
Besides the above operations, a restart can be made by performing a power-on reset
or resetting the inverter with the inverter's reset terminal.
REMARKS
• By entering the reset signal (RES) during operation, the inverter shuts off output
while it is reset, the data of the electronic overcurrent protection and regenerative
brake duty are reset, and the motor coasts.
• To resume operation, reset the inverter after confirming that the PU is connected
securely.
• The Pr. 75 value can be set any time. Also, if parameter (all) clear is executed,
this setting will not return to the initial value.
• When the inverter is stopped by the PU stop function, PS is displayed but an
alarm is not output.
- TRANSISTORIZED INVERTER 1
- Contents 6
- 1. WIRING 10
- .1 Japanese Version 11
- DC 0 to 5V 13
- DC 0 to 10V 13
- RS-485 Connector (*1) 13
- FR-S520- K-NA inverter 15
- Rated output current (A) 15
- Power supply capacity (kVA) 15
- AC input current (A) 15
- .3 European Version 16
- .4.1 Main circuit 18
- .4.2 Control circuit 18
- .5.2 Wiring instructions 21
- .5.3 Peripheral devices 22
- P<+>P1 27
- .5.8 Grounding precautions 28
- Is outgoing harmonic 30
- Terminal arrangement 33
- <AM> 33
- NA and Japanese version 34
- EC version 34
- .7 Input Terminals 37
- Reverse 38
- Forward 38
- Coasted to 39
- (1) Voltage input (10, 2, 5) 40
- (2) Current input (4, 5, AU) 41
- (1) Japanese version (FM) 43
- Inverter 44
- (2) NA and EC version (AM) 45
- RL, RM, RH, STR) 47
- Coasting time 49
- Communication Function) 50
- (2) RS-485 communication 51
- <Wiring methods> 52
- .10 Design Information 53
- FUNCTIONS 54
- .1 Function (Parameter) List 55
- 0 (bright) 63
- 63 (dark) 63
- .3.1 Torque boost 67
- Acceleration Deceleration 71
- Constant speed 71
- .3.7 DC injection brake 73
- .3.8 Starting frequency 74
- .3.9 Load pattern selection 75
- .3.13 Stall prevention 78
- .3.16 Frequency jump to 81
- .3.17 Speed display 82
- DisplayOperation 84
- Output signal 87
- .5.2 Zero current detection 90
- .6.1 Monitor display 91
- .6.3 Monitoring reference 93
- .7.1 Restart setting 93
- .10.1 Retry function 100
- .10.2 PWM carrier frequency 101
- .10.3 Applied motor 102
- <Setting> 103
- (1) PU operation interlock 109
- X16 Signal Operation Mode 110
- (2) PID action overview 111
- Too cold down 113
- Hot up 113
- (4) I/O signals 114
- (5) Parameter setting 114
- (6) Adjustment procedure 115
- (7) Calibration example 116
- .11.1 Slip compensation 118
- <Operating conditions> 119
- .12 Calibration Parameters 120
- The parameter 121
- (NA and EC version) 122
- .13 Clear Parameters 124
- (1) Operational functions 125
- <Computer programming> 129
- (1) Communication protocol 129
- (3) Data format 130
- (4) Data definitions 131
- Instruction 133
- [Example 1] H02 ... Forward 135
- [Example 2] H00 ... Stop 135
- [For example 1] 136
- <Error Code List> 137
- (6) Communication error 138
- (7) Program example 138
- PROM write selection 141
- .15.2 Buzzer sound control 142
- .15.3 PU contrast adjustment 143
- PROTECTIVE 145
- FUNCTIONS 145
- .1 Errors (Alarms) 146
- (2) Minor failures 150
- (3) Warnings 151
- (4) Write errors 152
- (Only when FR-PU04 is used) 154
- .1.4 Resetting the inverter 154
- .2 Troubleshooting 155
- .3.2 Check items 158
- .3.3 Periodic inspection 158
- .3.5 Pressure test 159
- <Preparation> 162
- <Checking method> 162
- .3.7 Replacement of parts 163
- AIR FLOW 164
- (2) Smoothing capacitors 165
- (3) Relays 165
- :Moving-iron type 166
- :Electrodynamometer type 166
- :Moving-coil type 166
- :Rectifier type 166
- 4. SPECIFI 169
- .1 Specification List 170
- (2) 3-phase 400V power supply 171
- .1.2 Common specifications 174
- .2 Outline Drawings 176
- Rating plate 177
- Parameter unit (FR-PU04) 178
- INSTRUCTIONS 179
- .1 Selecting Instructions 180
- .3 Operating Instructions 182
- (3) Installation 183
- (4) Setting 183
- (5) Power supply 183
- APPENDIX 185
- REVISIONS 191
Related products and manuals for Power supply units Mitsubishi FR-S500
(20 pages)
(298 pages)© 2020, manymanuals.com. All rights reserved. | 3.564 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals