Mitsubishi FR-S500 Instruction Manual Page 69
- Page / 191
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
60
Parameter Name
Factory
Setting
<EC version>
Setting
Range
Remarks
3
Base frequency 60Hz
<50Hz>
0 to 120Hz
19
Base frequency
voltage
- - -
<888>
0 to 500V,
888, - - -*1
888: 95% of power supply voltage*2
- - -: Same as power supply
voltage*3
Setting is enabled when Pr. 30 = "1".
47
Second V/F (base
frequency)
- - -
0 to
120Hz, - - -
- - -: Function invalid
Setting is enabled when Pr. 30 = "1".
*1 0 to 800V, 888, - - - for FR-S540-0.4K to 3.7K.
*2 1.9 times greater than the power supply voltage for the FR-S510W-0.1K to 0.75K.
*3 Twice greater than the power supply voltage for the FR-S510W-0.1K to 0.75K.
<Setting>
In Pr. 3 and Pr. 47, set the base frequency (motor's rated frequency).
Use the RT signal to switch between these two different base frequencies.
(Turn on the RT signal to make Pr. 47 valid.) (*)
When running the standard motor, generally set the "base frequency" to the rated
frequency of the motor. When running the motor using commercial power supply-
inverter switch-over operation, set the base frequency to the same value as the
power supply frequency.
When the frequency given on the motor's rating plate is only "50Hz", always set the
"base frequency" to "50Hz". Leaving the base frequency unchanged from "60Hz"
may make the voltage too low and the torque insufficient, resulting in an overload
trip. Special care must be taken when "1" is set in Pr. 14 "load pattern selection".
Set the base voltage (e.g. rated voltage of motor) in Pr. 19.
CAUTION
1. Set 60Hz in Pr. 3 "base frequency" when using a Mitsubishi constant-torque motor.
2. When automatic torque boost is selected, Pr. 47 is invalid. When automatic
torque boost is selected, setting "- - -" or "888" in Pr. 19 uses the rated output
voltage.
REMARKS
* The RT signal serves as the second function selection signal and makes the
other second functions valid.
♦
♦♦
♦
Related parameters
♦
♦♦
♦
When rated motor frequency is "50Hz"
⇒
Pr. 14 "load pattern selection" (refer to page 66)
RT signal (second function "Pr. 47") setting
⇒
Pr. 60 to Pr. 63 (input terminal function
selection) (refer to page 88)
Motor setting
⇒
Pr. 71 "applied motor" (refer to page 93)
Automatic torque boost selection
⇒
Pr. 98 "automatic torque boost selection (motor capacity)"
(refer to page 109)
- TRANSISTORIZED INVERTER 1
- Contents 6
- 1. WIRING 10
- .1 Japanese Version 11
- DC 0 to 5V 13
- DC 0 to 10V 13
- RS-485 Connector (*1) 13
- FR-S520- K-NA inverter 15
- Rated output current (A) 15
- Power supply capacity (kVA) 15
- AC input current (A) 15
- .3 European Version 16
- .4.1 Main circuit 18
- .4.2 Control circuit 18
- .5.2 Wiring instructions 21
- .5.3 Peripheral devices 22
- P<+>P1 27
- .5.8 Grounding precautions 28
- Is outgoing harmonic 30
- Terminal arrangement 33
- <AM> 33
- NA and Japanese version 34
- EC version 34
- .7 Input Terminals 37
- Reverse 38
- Forward 38
- Coasted to 39
- (1) Voltage input (10, 2, 5) 40
- (2) Current input (4, 5, AU) 41
- (1) Japanese version (FM) 43
- Inverter 44
- (2) NA and EC version (AM) 45
- RL, RM, RH, STR) 47
- Coasting time 49
- Communication Function) 50
- (2) RS-485 communication 51
- <Wiring methods> 52
- .10 Design Information 53
- FUNCTIONS 54
- .1 Function (Parameter) List 55
- 0 (bright) 63
- 63 (dark) 63
- .3.1 Torque boost 67
- Acceleration Deceleration 71
- Constant speed 71
- .3.7 DC injection brake 73
- .3.8 Starting frequency 74
- .3.9 Load pattern selection 75
- .3.13 Stall prevention 78
- .3.16 Frequency jump to 81
- .3.17 Speed display 82
- DisplayOperation 84
- Output signal 87
- .5.2 Zero current detection 90
- .6.1 Monitor display 91
- .6.3 Monitoring reference 93
- .7.1 Restart setting 93
- .10.1 Retry function 100
- .10.2 PWM carrier frequency 101
- .10.3 Applied motor 102
- <Setting> 103
- (1) PU operation interlock 109
- X16 Signal Operation Mode 110
- (2) PID action overview 111
- Too cold down 113
- Hot up 113
- (4) I/O signals 114
- (5) Parameter setting 114
- (6) Adjustment procedure 115
- (7) Calibration example 116
- .11.1 Slip compensation 118
- <Operating conditions> 119
- .12 Calibration Parameters 120
- The parameter 121
- (NA and EC version) 122
- .13 Clear Parameters 124
- (1) Operational functions 125
- <Computer programming> 129
- (1) Communication protocol 129
- (3) Data format 130
- (4) Data definitions 131
- Instruction 133
- [Example 1] H02 ... Forward 135
- [Example 2] H00 ... Stop 135
- [For example 1] 136
- <Error Code List> 137
- (6) Communication error 138
- (7) Program example 138
- PROM write selection 141
- .15.2 Buzzer sound control 142
- .15.3 PU contrast adjustment 143
- PROTECTIVE 145
- FUNCTIONS 145
- .1 Errors (Alarms) 146
- (2) Minor failures 150
- (3) Warnings 151
- (4) Write errors 152
- (Only when FR-PU04 is used) 154
- .1.4 Resetting the inverter 154
- .2 Troubleshooting 155
- .3.2 Check items 158
- .3.3 Periodic inspection 158
- .3.5 Pressure test 159
- <Preparation> 162
- <Checking method> 162
- .3.7 Replacement of parts 163
- AIR FLOW 164
- (2) Smoothing capacitors 165
- (3) Relays 165
- :Moving-iron type 166
- :Electrodynamometer type 166
- :Moving-coil type 166
- :Rectifier type 166
- 4. SPECIFI 169
- .1 Specification List 170
- (2) 3-phase 400V power supply 171
- .1.2 Common specifications 174
- .2 Outline Drawings 176
- Rating plate 177
- Parameter unit (FR-PU04) 178
- INSTRUCTIONS 179
- .1 Selecting Instructions 180
- .3 Operating Instructions 182
- (3) Installation 183
- (4) Setting 183
- (5) Power supply 183
- APPENDIX 185
- REVISIONS 191
Related products and manuals for Power supply units Mitsubishi FR-S500
(20 pages)
(298 pages)© 2020, manymanuals.com. All rights reserved. | 0.352 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals