Mitsubishi FR-S500 Instruction Manual Page 83
- Page / 191
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
74
2
.3.18 Biases and gains of the frequency setting voltage (current)
to
You can set the magnitude (slope) of the output frequency as desired in relation
to the external frequency setting signal (0 to 5V, 0 to 10V or 4 to 20mA DC).
The "bias" and "gain" functions are used to adjust the relationship between the
input signal entered from outside the inverter to set the output frequency, e.g. 0
to 5VDC, 0 to 10VDC or 4 to 20mADC, and the output frequency.
Frequency setting voltage signal
Factory setting
0Hz( )
C2
5V or 10V
(100% C4 )
0V
Pr.73
Output
frequency (Hz)
( Pr.38 )
60Hz<50Hz>
Frequency setting current signal
20mA
4mA
Factory setting
( Pr.39 )
60Hz<50Hz>
Output
frequency (Hz)
0Hz( )
C5
(0% C3 )
(Across
terminals
2-5)
(20% C6 )
(100% C7 )
(Across
terminals
4-5)
Parameter Name
Factory Setting
<EC version>
Setting
Range
Remarks
38
Frequency setting voltage gain
frequency
60Hz
<50Hz>
1 to 120Hz
39
Frequency setting current gain
frequency
60Hz
<50Hz>
1 to 120Hz
C2 (902)
Frequency setting voltage bias
frequency
0Hz 0 to 60Hz
C3 (902) Frequency setting voltage bias 0% * 0 to 300%
C4 (903) Frequency setting voltage gain 96% * 0 to 300%
C5 (904)
Frequency setting current bias
frequency
0Hz 0 to 60Hz
C6 (904) Frequency setting current bias 20% * 0 to 300%
C7 (905) Frequency setting current gain 100% * 0 to 300%
Setting is enabled
when Pr. 30 = "1".
* Settings may differ because of calibration parameters.
The parameter numbers within parentheses are those for use of the parameter unit (FR-PU04).
When the parameter unit (FR-PU04) is used, operation from the operation panel is not accepted.
POINT
Bias setting for 0-5VDC (0-10VDC) input Use calibration parameters C2, C3 for setting.
Gain setting for 0-5VDC (0-10VDC) input Use Pr. 38, calibration parameter C4 for
setting.
Bias setting for 4-20mADC input Use calibration parameters C5, C6 for
setting.
Gain setting for 4-20mADC input Use Pr. 39, calibration parameter C7 for
setting.
(For 4 to 20mADC input, set "4" in any of Pr. 60 to Pr. 63 (input terminal function
selection) and assign AU (current input selection) to any of terminals RH, RM, RL
and STR, and turn on the AU signal.)
- TRANSISTORIZED INVERTER 1
- Contents 6
- 1. WIRING 10
- .1 Japanese Version 11
- DC 0 to 5V 13
- DC 0 to 10V 13
- RS-485 Connector (*1) 13
- FR-S520- K-NA inverter 15
- Rated output current (A) 15
- Power supply capacity (kVA) 15
- AC input current (A) 15
- .3 European Version 16
- .4.1 Main circuit 18
- .4.2 Control circuit 18
- .5.2 Wiring instructions 21
- .5.3 Peripheral devices 22
- P<+>P1 27
- .5.8 Grounding precautions 28
- Is outgoing harmonic 30
- Terminal arrangement 33
- <AM> 33
- NA and Japanese version 34
- EC version 34
- .7 Input Terminals 37
- Reverse 38
- Forward 38
- Coasted to 39
- (1) Voltage input (10, 2, 5) 40
- (2) Current input (4, 5, AU) 41
- (1) Japanese version (FM) 43
- Inverter 44
- (2) NA and EC version (AM) 45
- RL, RM, RH, STR) 47
- Coasting time 49
- Communication Function) 50
- (2) RS-485 communication 51
- <Wiring methods> 52
- .10 Design Information 53
- FUNCTIONS 54
- .1 Function (Parameter) List 55
- 0 (bright) 63
- 63 (dark) 63
- .3.1 Torque boost 67
- Acceleration Deceleration 71
- Constant speed 71
- .3.7 DC injection brake 73
- .3.8 Starting frequency 74
- .3.9 Load pattern selection 75
- .3.13 Stall prevention 78
- .3.16 Frequency jump to 81
- .3.17 Speed display 82
- DisplayOperation 84
- Output signal 87
- .5.2 Zero current detection 90
- .6.1 Monitor display 91
- .6.3 Monitoring reference 93
- .7.1 Restart setting 93
- .10.1 Retry function 100
- .10.2 PWM carrier frequency 101
- .10.3 Applied motor 102
- <Setting> 103
- (1) PU operation interlock 109
- X16 Signal Operation Mode 110
- (2) PID action overview 111
- Too cold down 113
- Hot up 113
- (4) I/O signals 114
- (5) Parameter setting 114
- (6) Adjustment procedure 115
- (7) Calibration example 116
- .11.1 Slip compensation 118
- <Operating conditions> 119
- .12 Calibration Parameters 120
- The parameter 121
- (NA and EC version) 122
- .13 Clear Parameters 124
- (1) Operational functions 125
- <Computer programming> 129
- (1) Communication protocol 129
- (3) Data format 130
- (4) Data definitions 131
- Instruction 133
- [Example 1] H02 ... Forward 135
- [Example 2] H00 ... Stop 135
- [For example 1] 136
- <Error Code List> 137
- (6) Communication error 138
- (7) Program example 138
- PROM write selection 141
- .15.2 Buzzer sound control 142
- .15.3 PU contrast adjustment 143
- PROTECTIVE 145
- FUNCTIONS 145
- .1 Errors (Alarms) 146
- (2) Minor failures 150
- (3) Warnings 151
- (4) Write errors 152
- (Only when FR-PU04 is used) 154
- .1.4 Resetting the inverter 154
- .2 Troubleshooting 155
- .3.2 Check items 158
- .3.3 Periodic inspection 158
- .3.5 Pressure test 159
- <Preparation> 162
- <Checking method> 162
- .3.7 Replacement of parts 163
- AIR FLOW 164
- (2) Smoothing capacitors 165
- (3) Relays 165
- :Moving-iron type 166
- :Electrodynamometer type 166
- :Moving-coil type 166
- :Rectifier type 166
- 4. SPECIFI 169
- .1 Specification List 170
- (2) 3-phase 400V power supply 171
- .1.2 Common specifications 174
- .2 Outline Drawings 176
- Rating plate 177
- Parameter unit (FR-PU04) 178
- INSTRUCTIONS 179
- .1 Selecting Instructions 180
- .3 Operating Instructions 182
- (3) Installation 183
- (4) Setting 183
- (5) Power supply 183
- APPENDIX 185
- REVISIONS 191
Related products and manuals for Power supply units Mitsubishi FR-S500
(20 pages)
(298 pages)© 2020, manymanuals.com. All rights reserved. | 0.240 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals