Mitsubishi FR-S500 Instruction Manual Page 126
- Page / 191
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
117
2
2) Operation mode-based functions
Operation Mode
Operation
Location
Item
PU operation
External
operation
Computer link
operation
Run command
(start)
Enabled
Enabled
(Combined
operation mode)
Disabled
Running frequency
setting
Enabled
Enabled
(Combined
operation mode)
Disabled
Monitoring Enabled Enabled Enabled
Parameter write Enabled (*4) Disabled Disabled
Parameter read Enabled Enabled Enabled
Inverter reset Enabled Enabled Enabled
Operation panel
or FR-PU04
Stop command Enabled Enabled (*3) Enabled (*3)
Run command Disabled Disabled Enabled (*1)
Running frequency
setting (*)
Disabled Disabled Enabled (*1)
Monitoring Enabled Enabled Enabled
Parameter write Disabled Disabled Enabled (*4)
Parameter read Enabled Enabled Enabled
Inverter reset Disabled Disabled Enabled (*2)
On-computer
user program by
RS-485
communication
Stop command Disabled Disabled Enabled
Inverter reset Enabled Enabled Enabled
Run command
Enabled
(Combined
operation mode)
Enabled Enabled (*1)
Control circuit
external
terminal
Running frequency
setting
Enabled
(Combined
operation mode)
Enabled Enabled (*1)
*1. As set in the communication parameters n8 "operation command write" and n9
"speed command write". (refer to page 130)
*2. At occurrence of RS-485 communication error, the inverter cannot be reset
from the computer.
*3. As set in Pr. 75 "reset selection/PU stop selection".
*4. As set in Pr. 77 "parameter write disable selection".
CAUTION
* When the user program of the computer is used to make the running frequency
setting by RS-485 communication, setting can be made in the minimum setting
increments of 0.01Hz, but the setting may be written to the inverter in increments
of 0.1Hz. (0 is written in the second decimal place.)
POINT
To make RS-485 communication between the inverter and personal computer, the
operation mode must be set to the "computer link operation mode".
Pr. 79 "operation mode selection" ≠‚ "1, 3, 4"
and communication parameter n10 "link start mode selection" = "1"
Reset the inverter after setting the communication parameters n1, n2, n3, n4, n7,
n11. The values set are registered once the inverter is reset.
- TRANSISTORIZED INVERTER 1
- Contents 6
- 1. WIRING 10
- .1 Japanese Version 11
- DC 0 to 5V 13
- DC 0 to 10V 13
- RS-485 Connector (*1) 13
- FR-S520- K-NA inverter 15
- Rated output current (A) 15
- Power supply capacity (kVA) 15
- AC input current (A) 15
- .3 European Version 16
- .4.1 Main circuit 18
- .4.2 Control circuit 18
- .5.2 Wiring instructions 21
- .5.3 Peripheral devices 22
- P<+>P1 27
- .5.8 Grounding precautions 28
- Is outgoing harmonic 30
- Terminal arrangement 33
- <AM> 33
- NA and Japanese version 34
- EC version 34
- .7 Input Terminals 37
- Reverse 38
- Forward 38
- Coasted to 39
- (1) Voltage input (10, 2, 5) 40
- (2) Current input (4, 5, AU) 41
- (1) Japanese version (FM) 43
- Inverter 44
- (2) NA and EC version (AM) 45
- RL, RM, RH, STR) 47
- Coasting time 49
- Communication Function) 50
- (2) RS-485 communication 51
- <Wiring methods> 52
- .10 Design Information 53
- FUNCTIONS 54
- .1 Function (Parameter) List 55
- 0 (bright) 63
- 63 (dark) 63
- .3.1 Torque boost 67
- Acceleration Deceleration 71
- Constant speed 71
- .3.7 DC injection brake 73
- .3.8 Starting frequency 74
- .3.9 Load pattern selection 75
- .3.13 Stall prevention 78
- .3.16 Frequency jump to 81
- .3.17 Speed display 82
- DisplayOperation 84
- Output signal 87
- .5.2 Zero current detection 90
- .6.1 Monitor display 91
- .6.3 Monitoring reference 93
- .7.1 Restart setting 93
- .10.1 Retry function 100
- .10.2 PWM carrier frequency 101
- .10.3 Applied motor 102
- <Setting> 103
- (1) PU operation interlock 109
- X16 Signal Operation Mode 110
- (2) PID action overview 111
- Too cold down 113
- Hot up 113
- (4) I/O signals 114
- (5) Parameter setting 114
- (6) Adjustment procedure 115
- (7) Calibration example 116
- .11.1 Slip compensation 118
- <Operating conditions> 119
- .12 Calibration Parameters 120
- The parameter 121
- (NA and EC version) 122
- .13 Clear Parameters 124
- (1) Operational functions 125
- <Computer programming> 129
- (1) Communication protocol 129
- (3) Data format 130
- (4) Data definitions 131
- Instruction 133
- [Example 1] H02 ... Forward 135
- [Example 2] H00 ... Stop 135
- [For example 1] 136
- <Error Code List> 137
- (6) Communication error 138
- (7) Program example 138
- PROM write selection 141
- .15.2 Buzzer sound control 142
- .15.3 PU contrast adjustment 143
- PROTECTIVE 145
- FUNCTIONS 145
- .1 Errors (Alarms) 146
- (2) Minor failures 150
- (3) Warnings 151
- (4) Write errors 152
- (Only when FR-PU04 is used) 154
- .1.4 Resetting the inverter 154
- .2 Troubleshooting 155
- .3.2 Check items 158
- .3.3 Periodic inspection 158
- .3.5 Pressure test 159
- <Preparation> 162
- <Checking method> 162
- .3.7 Replacement of parts 163
- AIR FLOW 164
- (2) Smoothing capacitors 165
- (3) Relays 165
- :Moving-iron type 166
- :Electrodynamometer type 166
- :Moving-coil type 166
- :Rectifier type 166
- 4. SPECIFI 169
- .1 Specification List 170
- (2) 3-phase 400V power supply 171
- .1.2 Common specifications 174
- .2 Outline Drawings 176
- Rating plate 177
- Parameter unit (FR-PU04) 178
- INSTRUCTIONS 179
- .1 Selecting Instructions 180
- .3 Operating Instructions 182
- (3) Installation 183
- (4) Setting 183
- (5) Power supply 183
- APPENDIX 185
- REVISIONS 191
Related products and manuals for Power supply units Mitsubishi FR-S500
(20 pages)
(298 pages)© 2020, manymanuals.com. All rights reserved. | 4.436 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals