Mitsubishi FR-S500 Instruction Manual Page 88
- Page / 191
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
79
2
2
.4.2 Output frequency detection
The output frequency detection
signal (FU) is output when the
output frequency reaches or
exceeds the setting. This function
can be used for electromagnetic
brake operation, open signal, etc.
You can also set the detection of
the frequency used exclusively for
reverse rotation.
Forward
rotation
Reverse
rotation
Time
Output
signal
FU
Output
frequency (Hz)
Pr.42
Pr.43
ON
ON
OFF OFF OFF
This function is effective for switching the timing of electromagnetic brake
operation between forward rotation (rise) and reverse rotation (fall) during vertical
lift operation, etc.
Parameter Name
Factory
Setting
Setting
Range
Remarks
42
Output frequency
detection
6Hz 0 to 120Hz
43
Output frequency
detection for reverse
rotation
- - -
0 to 120Hz,
- - -
- - -: Same as
Pr. 42 setting
Setting is
enabled
when Pr. 30
= "1".
<Setting>
Refer to the above chart and set the corresponding parameters.
When Pr. 43 "output frequency detection for reverse rotation"
≠
"- - -", the Pr.42
setting applies to forward rotation and the Pr.43 setting applies to reverse rotation.
Use Pr. 64 or Pr. 65 (output terminal function selection) to assign the terminal used
for FU signal output.
CAUTION
Using Pr. 64 or Pr. 65 to change terminal assignment may affect the other functions.
Make setting after confirming the function of each terminal.
♦
♦♦
♦
Related parameters
♦
♦♦
♦
Assignment of FU signal to terminal
⇒
Pr. 64 "RUN terminal function selection", Pr. 65 "A, B, C
terminal function selection" (refer to page 90)
, Refer to , (page 62).
Refer to
(page 58).
Refer to (page 59).
- TRANSISTORIZED INVERTER 1
- Contents 6
- 1. WIRING 10
- .1 Japanese Version 11
- DC 0 to 5V 13
- DC 0 to 10V 13
- RS-485 Connector (*1) 13
- FR-S520- K-NA inverter 15
- Rated output current (A) 15
- Power supply capacity (kVA) 15
- AC input current (A) 15
- .3 European Version 16
- .4.1 Main circuit 18
- .4.2 Control circuit 18
- .5.2 Wiring instructions 21
- .5.3 Peripheral devices 22
- P<+>P1 27
- .5.8 Grounding precautions 28
- Is outgoing harmonic 30
- Terminal arrangement 33
- <AM> 33
- NA and Japanese version 34
- EC version 34
- .7 Input Terminals 37
- Reverse 38
- Forward 38
- Coasted to 39
- (1) Voltage input (10, 2, 5) 40
- (2) Current input (4, 5, AU) 41
- (1) Japanese version (FM) 43
- Inverter 44
- (2) NA and EC version (AM) 45
- RL, RM, RH, STR) 47
- Coasting time 49
- Communication Function) 50
- (2) RS-485 communication 51
- <Wiring methods> 52
- .10 Design Information 53
- FUNCTIONS 54
- .1 Function (Parameter) List 55
- 0 (bright) 63
- 63 (dark) 63
- .3.1 Torque boost 67
- Acceleration Deceleration 71
- Constant speed 71
- .3.7 DC injection brake 73
- .3.8 Starting frequency 74
- .3.9 Load pattern selection 75
- .3.13 Stall prevention 78
- .3.16 Frequency jump to 81
- .3.17 Speed display 82
- DisplayOperation 84
- Output signal 87
- .5.2 Zero current detection 90
- .6.1 Monitor display 91
- .6.3 Monitoring reference 93
- .7.1 Restart setting 93
- .10.1 Retry function 100
- .10.2 PWM carrier frequency 101
- .10.3 Applied motor 102
- <Setting> 103
- (1) PU operation interlock 109
- X16 Signal Operation Mode 110
- (2) PID action overview 111
- Too cold down 113
- Hot up 113
- (4) I/O signals 114
- (5) Parameter setting 114
- (6) Adjustment procedure 115
- (7) Calibration example 116
- .11.1 Slip compensation 118
- <Operating conditions> 119
- .12 Calibration Parameters 120
- The parameter 121
- (NA and EC version) 122
- .13 Clear Parameters 124
- (1) Operational functions 125
- <Computer programming> 129
- (1) Communication protocol 129
- (3) Data format 130
- (4) Data definitions 131
- Instruction 133
- [Example 1] H02 ... Forward 135
- [Example 2] H00 ... Stop 135
- [For example 1] 136
- <Error Code List> 137
- (6) Communication error 138
- (7) Program example 138
- PROM write selection 141
- .15.2 Buzzer sound control 142
- .15.3 PU contrast adjustment 143
- PROTECTIVE 145
- FUNCTIONS 145
- .1 Errors (Alarms) 146
- (2) Minor failures 150
- (3) Warnings 151
- (4) Write errors 152
- (Only when FR-PU04 is used) 154
- .1.4 Resetting the inverter 154
- .2 Troubleshooting 155
- .3.2 Check items 158
- .3.3 Periodic inspection 158
- .3.5 Pressure test 159
- <Preparation> 162
- <Checking method> 162
- .3.7 Replacement of parts 163
- AIR FLOW 164
- (2) Smoothing capacitors 165
- (3) Relays 165
- :Moving-iron type 166
- :Electrodynamometer type 166
- :Moving-coil type 166
- :Rectifier type 166
- 4. SPECIFI 169
- .1 Specification List 170
- (2) 3-phase 400V power supply 171
- .1.2 Common specifications 174
- .2 Outline Drawings 176
- Rating plate 177
- Parameter unit (FR-PU04) 178
- INSTRUCTIONS 179
- .1 Selecting Instructions 180
- .3 Operating Instructions 182
- (3) Installation 183
- (4) Setting 183
- (5) Power supply 183
- APPENDIX 185
- REVISIONS 191
Related products and manuals for Power supply units Mitsubishi FR-S500
(20 pages)
(298 pages)© 2020, manymanuals.com. All rights reserved. | 0.428 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals