Mitsubishi HD-5000A Instruction Manual Page 15
- Page / 356
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4
8.2.3 Adjustment procedure by auto tuning............................................................................................ 8- 5
8.2.4 Response level setting in auto tuning mode .................................................................................. 8- 6
8.3 Manual mode 1 (simple manual adjustment)....................................................................................... 8- 7
8.3.1 Operation of manual mode 1 ........................................................................................................... 8- 7
8.3.2 Adjustment by manual mode 1 ....................................................................................................... 8- 7
8.4 Interpolation mode ................................................................................................................................. 8-10
8.5 Differences in auto tuning between MELSERVO-J2 and MELSERVO-J2-Super.......................... 8-11
8.5.1 Response level setting ..................................................................................................................... 8-11
8.5.2 Auto tuning selection....................................................................................................................... 8-11
9. SPECIAL ADJUSTMENT FUNCTIONS 9- 1 to 9-10
9.1 Function block diagram .......................................................................................................................... 9- 1
9.2 Machine resonance suppression filter ................................................................................................... 9- 1
9.3 Adaptive vibration suppression control................................................................................................. 9- 3
9.4 Low-pass filter ......................................................................................................................................... 9- 5
9.5 Gain changing function........................................................................................................................... 9- 5
9.5.1 Applications....................................................................................................................................... 9- 5
9.5.2 Function block diagram ................................................................................................................... 9- 6
9.5.3 Parameters ........................................................................................................................................ 9- 7
9.5.4 Gain changing operation.................................................................................................................. 9- 9
10. INSPECTION 10- 1 to 10- 2
11. TROUBLESHOOTING 11- 1 to 11-12
11.1 Trouble at start-up ..............................................................................................................................11- 1
11.2 When alarm or warning has occurred ...............................................................................................11- 2
11.2.1 Alarms and warning list .............................................................................................................. 11- 2
11.2.2 Remedies for alarms..................................................................................................................... 11- 3
11.2.3 Remedies for warnings................................................................................................................ 11-11
11.3 MR-DP60 external digital display error...........................................................................................11-12
12. OUTLINE DIMENSION DRAWINGS 12- 1 to 12- 8
12.1 Servo amplifiers................................................................................................................................... 12- 1
12.2 Connectors............................................................................................................................................12- 6
13. CHARACTERISTICS 13- 1 to 13- 8
13.1 Overload protection characteristics ...................................................................................................13- 1
13.2 Power supply equipment capacity and generated loss .................................................................... 13- 2
13.3 Dynamic brake characteristics........................................................................................................... 13- 4
13.3.1 Dynamic brake operation............................................................................................................. 13- 4
13.3.2 The dynamic brake at the load inertia moment ........................................................................ 13- 6
13.4 Encoder cable flexing life .................................................................................................................... 13- 6
13.5 Inrush Currents at Power-On of Main Circuit and Control Circuit .............................................. 13- 7
- J2-Super Series 1
- Safety Instructions 2
- WARNING 3
- CAUTION 3
- About processing of waste 7
- PE terminals 9
- Crimping terminal 9
- Insulating tube 9
- 1,L2 and leave L3 open 21
- CN1A CN1B 23
- 81 102 103 33
- MODE UP DOWN 35
- Magnetic 43
- Regenerative option 43
- (Note 1) 43
- 2. INSTALLATION 46
- 3. SIGNALS AND WIRING 50
- Servo motor 77
- PE terminal 77
- Control box 77
- Electromagnetic brake 83
- Approx. 10mm 86
- Less than 0.5mm 86
- 4. OPERATION 100
- Ignored 101
- Forward rotation jog 117
- Reverse rotation jog 117
- Forward rotation 118
- Deceleration time 125
- Creep speed 125
- Parameter No. 10 125
- Parameter No. 41 125
- Home position 132
- Home position return 132
- Proximity dog 132
- CAUTION 133
- WARNING 134
- Parameter No.2 135
- 0: Incremental system 135
- Parameter No. 0 139
- 5. PARAMETERS 142
- 0: Base circuit switched off 156
- Electronic gear 162
- Parameters No. 4, 5 162
- Parameter No. 17 164
- Max. torque 165
- Alarm history clear 167
- 0: Invalid (not cleared) 167
- 1: Valid (cleared) 167
- Parameter No. 16 167
- Expansion parameter 1 190
- Expansion parameter 2 190
- 7. DISPLAY AND OPERATION 191
- Expansion parameters 2 200
- Expansion parameters 1 200
- 8. GENERAL GAIN ADJUSTMENT 210
- Parameter No. 3 220
- Auto tuning selection 220
- Parameter No. 63 226
- Low-pass filter selection 226
- 1: Invalid 226
- Command frequency kpps 229
- Droop pulses pulse 229
- Servo motor speed r/min 229
- 10. INSPECTION 232
- 11. TROUBLESHOOTING 234
- Checking method 237
- AL.24 occurs if the servo is 238
- MITSUBISHI 248
- Servo amplifier 249
- [kg] ([lb]) 249
- MR-J2S-500CL 4.9 (10.8) 249
- MR-J2S-700CL 7.2 (15.9) 250
- 13. CHARACTERISTICS 254
- (Outside) 256
- (Inside) 256
- Air flow 256
- 82.5 40 (1.58) 265
- Accessory screw 266
- For MR-J2S-500CL 267
- For MR-J2S-700CL 267
- (Note 9) 271
- N/ P/ PR 272
- 2- 5 hole 274
- (Screw size: M4) 274
- Model : MR-CPCATCBL3M 285
- Model : MR-J2TBL M 287
- EM1 PESG 288
- LG LG MO1 MO2 288
- COM DI MBR EMGO 288
- TXD TXD RXDRXD P5 LG 290
- [Unit: mm (in)] 291
- 12V 0V A B 292
- 3- 4.8(0.189) 293
- Panel cutting 293
- [Unit: mm(in)] 293
- Conductor 295
- Insulation sheath 295
- Strip the cable sheath of 301
- FR-BLF(MR-J2S-350CL or more) 303
- MR-J2S-40CL 306
- [Unit: mm] 309
- 15. COMMUNICATION FUNCTIONS 312
- 0123456 7 314
- (LSB) (MSB) 314
- 1 frame (11bits) 314
- 3000000929 327
- PPENDIX 348
- REVISIONS 352
© 2020, manymanuals.com. All rights reserved. | 1.709 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals