Mitsubishi HD-5000A Instruction Manual Page 265
- Page / 356
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
14 - 4
14. OPTIONS AND AUXILIARY EQUIPMENT
(4) Connection of the regenerative option
POINT
When using the MR-RB50 and MR-RB51, cooling by a cooling fan is
required. Please obtain a cooling fan at your discretion.
The regenerative option will cause a temperature rise of
100 degrees relative to the ambient
temperature. Fully examine heat dissipation, installation position, used cables, etc. before installing
the option. For wiring, use flame-resistant cables and keep them clear of the regenerative option body.
Always use twisted cables of max. 5m(16.4ft) length for connection with the servo amplifier.
(a) MR-J2S-350CL or less
Always remove the wiring from across P-D and fit the regenerative option across P-C.
The G3 and G4 terminals act as a thermal sensor. G3-G4 are disconnected when the regenerative
option overheats abnormally.
Servo amplifier
Regenerative option
Always remove the lead from across P-D.
D
P
C
G4
G3
(Note 2)
5m (16.4 ft) max.
Cooling fan(Note 1)
C
P
Note 1. When using the MR-RB50, forcibly cool it with a cooling fan (92 92, minimum air flow: 1.0m
3
).
2. Make up a sequence which will switch off the magnetic contactor (MC) when abnormal heating occurs.
G3-G4 contact specifications
Maximum voltage: 120V AC/DC
Maximum current: 0.5A/4.8VDC
Maximum capacity: 2.4VA
For the MR-RB50 install the cooling fan as shown.
82.5 40 (1.58)
82.5133
Cooling fan installation screw hole dimensions
2-M3 screw hole
(for cooling fan installation)
Depth 10 or less
(Screw hole already
machined)
Cooling fan Terminal block
Thermal relay
Installation surface
Horizontal installation
Vertical
installation
Top
Bottom
(3.25)
(5.24)
(3.25)
[Unit : mm(in)]
- J2-Super Series 1
- Safety Instructions 2
- WARNING 3
- CAUTION 3
- About processing of waste 7
- PE terminals 9
- Crimping terminal 9
- Insulating tube 9
- 1,L2 and leave L3 open 21
- CN1A CN1B 23
- 81 102 103 33
- MODE UP DOWN 35
- Magnetic 43
- Regenerative option 43
- (Note 1) 43
- 2. INSTALLATION 46
- 3. SIGNALS AND WIRING 50
- Servo motor 77
- PE terminal 77
- Control box 77
- Electromagnetic brake 83
- Approx. 10mm 86
- Less than 0.5mm 86
- 4. OPERATION 100
- Ignored 101
- Forward rotation jog 117
- Reverse rotation jog 117
- Forward rotation 118
- Deceleration time 125
- Creep speed 125
- Parameter No. 10 125
- Parameter No. 41 125
- Home position 132
- Home position return 132
- Proximity dog 132
- CAUTION 133
- WARNING 134
- Parameter No.2 135
- 0: Incremental system 135
- Parameter No. 0 139
- 5. PARAMETERS 142
- 0: Base circuit switched off 156
- Electronic gear 162
- Parameters No. 4, 5 162
- Parameter No. 17 164
- Max. torque 165
- Alarm history clear 167
- 0: Invalid (not cleared) 167
- 1: Valid (cleared) 167
- Parameter No. 16 167
- Expansion parameter 1 190
- Expansion parameter 2 190
- 7. DISPLAY AND OPERATION 191
- Expansion parameters 2 200
- Expansion parameters 1 200
- 8. GENERAL GAIN ADJUSTMENT 210
- Parameter No. 3 220
- Auto tuning selection 220
- Parameter No. 63 226
- Low-pass filter selection 226
- 1: Invalid 226
- Command frequency kpps 229
- Droop pulses pulse 229
- Servo motor speed r/min 229
- 10. INSPECTION 232
- 11. TROUBLESHOOTING 234
- Checking method 237
- AL.24 occurs if the servo is 238
- MITSUBISHI 248
- Servo amplifier 249
- [kg] ([lb]) 249
- MR-J2S-500CL 4.9 (10.8) 249
- MR-J2S-700CL 7.2 (15.9) 250
- 13. CHARACTERISTICS 254
- (Outside) 256
- (Inside) 256
- Air flow 256
- 82.5 40 (1.58) 265
- Accessory screw 266
- For MR-J2S-500CL 267
- For MR-J2S-700CL 267
- (Note 9) 271
- N/ P/ PR 272
- 2- 5 hole 274
- (Screw size: M4) 274
- Model : MR-CPCATCBL3M 285
- Model : MR-J2TBL M 287
- EM1 PESG 288
- LG LG MO1 MO2 288
- COM DI MBR EMGO 288
- TXD TXD RXDRXD P5 LG 290
- [Unit: mm (in)] 291
- 12V 0V A B 292
- 3- 4.8(0.189) 293
- Panel cutting 293
- [Unit: mm(in)] 293
- Conductor 295
- Insulation sheath 295
- Strip the cable sheath of 301
- FR-BLF(MR-J2S-350CL or more) 303
- MR-J2S-40CL 306
- [Unit: mm] 309
- 15. COMMUNICATION FUNCTIONS 312
- 0123456 7 314
- (LSB) (MSB) 314
- 1 frame (11bits) 314
- 3000000929 327
- PPENDIX 348
- REVISIONS 352
© 2020, manymanuals.com. All rights reserved. | 0.372 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals