Mitsubishi HD-5000A Instruction Manual Page 68
- Page / 356
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
3 - 19
3. SIGNALS AND WIRING
3.6.2 Detailed description of the interfaces
This section gives the details of the I/O signal interfaces (refer to I/O Division in the table) indicated in
sections 3.3.2. Refer to this section and connect the interfaces with the external equipment.
(1) Digital input interface DI-1
Give a signal with a relay or open collector transistor. Source input is also possible. Refer to (6) in this
section.
For use of internal power supply For use of external power supply
VDD
COM
24VDC
SGTR
Servo amplifier
R: Approx. 4.7k
SON, etc.
(Note)
For a transistor
Approx. 5mA
V
CES
1.0V
I
CEO 100 A
Switch
COM
SG
Switch
SON, etc.
24VDC
200mA or more
Servo amplifier
R: Approx. 4.7k
VDD
24VDC
Do not connect
VDD-COM.
Note. This also applies to the use of the external power supply.
(2) Digital output interface DO-1
A lamp, relay or photocoupler can be driven. Provide a diode (D) for an inductive load, or an inrush
current suppressing resister (R) for a lamp load. (Permissible current: 40mA or less, inrush current:
100mA or less) A maximum of 2.6V voltage drop occurs in the servo amplifier.
(a) Inductive load
For use of internal power supply For use of external power supply
COM
ALM, etc
SG
Load
Servo amplifier
VDD
24VDC
If the diode is not
connected as shown,
the servo amplifier
will be damaged.
COM
ALM, etc
SG
Load
Servo amplifier
VDD
24VDC
If the diode is not
connected as shown,
the servo amplifier
will be damaged.
Do not connect
VDD-COM.
(Note)
24VDC
10%
Note. If the voltage drop (maximum of 2.6V) interferes with the
relay operation, apply high voltage (up to 26.4V) from
external source.
- J2-Super Series 1
- Safety Instructions 2
- WARNING 3
- CAUTION 3
- About processing of waste 7
- PE terminals 9
- Crimping terminal 9
- Insulating tube 9
- 1,L2 and leave L3 open 21
- CN1A CN1B 23
- 81 102 103 33
- MODE UP DOWN 35
- Magnetic 43
- Regenerative option 43
- (Note 1) 43
- 2. INSTALLATION 46
- 3. SIGNALS AND WIRING 50
- Servo motor 77
- PE terminal 77
- Control box 77
- Electromagnetic brake 83
- Approx. 10mm 86
- Less than 0.5mm 86
- 4. OPERATION 100
- Ignored 101
- Forward rotation jog 117
- Reverse rotation jog 117
- Forward rotation 118
- Deceleration time 125
- Creep speed 125
- Parameter No. 10 125
- Parameter No. 41 125
- Home position 132
- Home position return 132
- Proximity dog 132
- CAUTION 133
- WARNING 134
- Parameter No.2 135
- 0: Incremental system 135
- Parameter No. 0 139
- 5. PARAMETERS 142
- 0: Base circuit switched off 156
- Electronic gear 162
- Parameters No. 4, 5 162
- Parameter No. 17 164
- Max. torque 165
- Alarm history clear 167
- 0: Invalid (not cleared) 167
- 1: Valid (cleared) 167
- Parameter No. 16 167
- Expansion parameter 1 190
- Expansion parameter 2 190
- 7. DISPLAY AND OPERATION 191
- Expansion parameters 2 200
- Expansion parameters 1 200
- 8. GENERAL GAIN ADJUSTMENT 210
- Parameter No. 3 220
- Auto tuning selection 220
- Parameter No. 63 226
- Low-pass filter selection 226
- 1: Invalid 226
- Command frequency kpps 229
- Droop pulses pulse 229
- Servo motor speed r/min 229
- 10. INSPECTION 232
- 11. TROUBLESHOOTING 234
- Checking method 237
- AL.24 occurs if the servo is 238
- MITSUBISHI 248
- Servo amplifier 249
- [kg] ([lb]) 249
- MR-J2S-500CL 4.9 (10.8) 249
- MR-J2S-700CL 7.2 (15.9) 250
- 13. CHARACTERISTICS 254
- (Outside) 256
- (Inside) 256
- Air flow 256
- 82.5 40 (1.58) 265
- Accessory screw 266
- For MR-J2S-500CL 267
- For MR-J2S-700CL 267
- (Note 9) 271
- N/ P/ PR 272
- 2- 5 hole 274
- (Screw size: M4) 274
- Model : MR-CPCATCBL3M 285
- Model : MR-J2TBL M 287
- EM1 PESG 288
- LG LG MO1 MO2 288
- COM DI MBR EMGO 288
- TXD TXD RXDRXD P5 LG 290
- [Unit: mm (in)] 291
- 12V 0V A B 292
- 3- 4.8(0.189) 293
- Panel cutting 293
- [Unit: mm(in)] 293
- Conductor 295
- Insulation sheath 295
- Strip the cable sheath of 301
- FR-BLF(MR-J2S-350CL or more) 303
- MR-J2S-40CL 306
- [Unit: mm] 309
- 15. COMMUNICATION FUNCTIONS 312
- 0123456 7 314
- (LSB) (MSB) 314
- 1 frame (11bits) 314
- 3000000929 327
- PPENDIX 348
- REVISIONS 352
© 2020, manymanuals.com. All rights reserved. | 0.374 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals