Mitsubishi HD-5000A Instruction Manual Page 332
- Page / 356
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
15 - 21
15. COMMUNICATION FUNCTIONS
15.12.4 External I/O signal statuses
(1) Reading of input device statuses
Read the statuses of the input devices.
(a) Transmission
Transmit command [1][2] and data No. [0][0].
Command Data No.
[1][2] [0][0]
(b) Reply
The slave station sends back the statuses of the input pins.
b31 b0
0:OFF
1:ON
b1
Command of each bit is transmitted to the master
station as hexadecimal data.
bit Signal name bit Signal name bit Signal name
0 Servo-on (SON) 12 Reverse rotation start (ST2)
24
Temporary stop/restart (STP)
1 Forward rotation stroke limit (LSP) 13
2 Reverse rotation stroke limit (LSN) 14
25
Manual pulse generator
multiplication 1 (TP0)
3 External torque limit selection (TL) 15
4 Internal torque limit selection (TL2) 16 Forced stop (EMG)
26
Manual pulse generator
multiplication 2 (TP1)
5 Proportion control selection (PC) 17 Automatic/manual selection (MD0)
27
Gain switch (CDP)
6 Reset (RES) 18 Proximity dog (DOG)
28
7 19 Program No. selection 1 (DI0)
29
Program input 1 (PI1)
8 20 Program No. selection 2 (DI1)
30
Program input 2 (PI2)
9 21 Program No. selection 3 (DI2)
31
Program input 3 (PI3)
10 Current position latch input (LPS) 22 Program No. selection 4 (DI3)
11 Forward rotation start (ST1) 23 Override selection (OVR)
(2) External input pin status read
Read the ON/OFF statuses of the external output pins.
(a) Transmission
Transmit command [1][2] and data No. [4][0].
Command Data No.
[1][2] [4][0]
(b) Reply
The ON/OFF statuses of the input pins are sent back.
b31 b0
0:OFF
1:ON
b1
Command of each bit is transmitted to the master
station as hexadecimal data.
bit External input pin bit External input pin
0 CN1B-16 5 CN1A-8
1 CN1B-17 6 CN1B-7
2 CN1B-15 7 CN1B-8
3 CN1B-5 8 CN1B-9
4 CN1B-14
9 CN1A-19
- J2-Super Series 1
- Safety Instructions 2
- WARNING 3
- CAUTION 3
- About processing of waste 7
- PE terminals 9
- Crimping terminal 9
- Insulating tube 9
- 1,L2 and leave L3 open 21
- CN1A CN1B 23
- 81 102 103 33
- MODE UP DOWN 35
- Magnetic 43
- Regenerative option 43
- (Note 1) 43
- 2. INSTALLATION 46
- 3. SIGNALS AND WIRING 50
- Servo motor 77
- PE terminal 77
- Control box 77
- Electromagnetic brake 83
- Approx. 10mm 86
- Less than 0.5mm 86
- 4. OPERATION 100
- Ignored 101
- Forward rotation jog 117
- Reverse rotation jog 117
- Forward rotation 118
- Deceleration time 125
- Creep speed 125
- Parameter No. 10 125
- Parameter No. 41 125
- Home position 132
- Home position return 132
- Proximity dog 132
- CAUTION 133
- WARNING 134
- Parameter No.2 135
- 0: Incremental system 135
- Parameter No. 0 139
- 5. PARAMETERS 142
- 0: Base circuit switched off 156
- Electronic gear 162
- Parameters No. 4, 5 162
- Parameter No. 17 164
- Max. torque 165
- Alarm history clear 167
- 0: Invalid (not cleared) 167
- 1: Valid (cleared) 167
- Parameter No. 16 167
- Expansion parameter 1 190
- Expansion parameter 2 190
- 7. DISPLAY AND OPERATION 191
- Expansion parameters 2 200
- Expansion parameters 1 200
- 8. GENERAL GAIN ADJUSTMENT 210
- Parameter No. 3 220
- Auto tuning selection 220
- Parameter No. 63 226
- Low-pass filter selection 226
- 1: Invalid 226
- Command frequency kpps 229
- Droop pulses pulse 229
- Servo motor speed r/min 229
- 10. INSPECTION 232
- 11. TROUBLESHOOTING 234
- Checking method 237
- AL.24 occurs if the servo is 238
- MITSUBISHI 248
- Servo amplifier 249
- [kg] ([lb]) 249
- MR-J2S-500CL 4.9 (10.8) 249
- MR-J2S-700CL 7.2 (15.9) 250
- 13. CHARACTERISTICS 254
- (Outside) 256
- (Inside) 256
- Air flow 256
- 82.5 40 (1.58) 265
- Accessory screw 266
- For MR-J2S-500CL 267
- For MR-J2S-700CL 267
- (Note 9) 271
- N/ P/ PR 272
- 2- 5 hole 274
- (Screw size: M4) 274
- Model : MR-CPCATCBL3M 285
- Model : MR-J2TBL M 287
- EM1 PESG 288
- LG LG MO1 MO2 288
- COM DI MBR EMGO 288
- TXD TXD RXDRXD P5 LG 290
- [Unit: mm (in)] 291
- 12V 0V A B 292
- 3- 4.8(0.189) 293
- Panel cutting 293
- [Unit: mm(in)] 293
- Conductor 295
- Insulation sheath 295
- Strip the cable sheath of 301
- FR-BLF(MR-J2S-350CL or more) 303
- MR-J2S-40CL 306
- [Unit: mm] 309
- 15. COMMUNICATION FUNCTIONS 312
- 0123456 7 314
- (LSB) (MSB) 314
- 1 frame (11bits) 314
- 3000000929 327
- PPENDIX 348
- REVISIONS 352
© 2020, manymanuals.com. All rights reserved. | 1.323 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals